Filter
Top Products
194
Settings Common to All Modes (System Function)
[F3 (SOUND)]
[F4 (USB)]
You must switch the USB Mode before you connect the Fantom-Xa to your computer via the USB cable. If you change this setting while the
Fantom-Xa is connected, the computer may fail to recognize it correctly.
For details on connections to your computer in each USB Mode, refer to
Connections
(p. 207).
Parameter
Value Explanation
Sound Generator
Master Tune
415.3–466.2 Hz Overall tuning of the Fantom-Xa
The display shows the frequency of the A4 note (center A).
Master Key Shift -24– +24 Shifts the overall pitch of the Fantom-Xa in semitone steps.
Master Level 0–127 Volume of the entire Fantom-Xa
Output Gain -12– 12 dB Output gain from the Fantom-Xa’s Output
When, for example, there are relatively few voices being sounded, boosting the output gain
can let you attain the most suitable output level for recording and other purposes.
Mix/Parallel MIX, PARALLEL How the sound of the entire Fantom-Xa will be output
MIX:
Set this to have the collective output of all sounds output from the OUTPUT A (MIX)
jacks. When you want to check the final overall sound being output, set to MIX.
PARALLEL:
Output according to each Output Assign settings.
* Sounds which are set in the respective Output Assign to be output from the INDIVIDUAL 3 jack are
output from the left OUTPUT A (MIX) jack; sounds which are set to be output from the INDIVIDU-
AL 4 jack are output from the right OUTPUT A (MIX) jack.
* Sounds output from the PHONES jack are the same as those output from the OUTPUT A (MIX)
jacks. Therefore, any sounds set with Output Assign to be output from the OUTPUT B jacks is not
output from the PHONES jack. Be sure to have any sound you want to hear through the headphones
set to “MIX.”
Preview
Preview Mode
SINGLE,
CHORD,
PHRASE
SINGLE:
The notes specified by Preview 1–4 Note Number will sound successively one by one.
CHORD:
The notes specified by Preview 1–4 Note Number will sound simultaneously.
PHRASE:
The Phrase associated with the patch’s type/category is played.
Preview 1–4 Note
Number
C - –G9 Specify the pitch of the four notes that will sound when the Preview Mode is set to “SINGLE”
or “CHORD.”
* If “PHRASE” is selected for the Preview Mode parameter, these settings will have no effect.
Preview 1–4 Velocity OFF, 1–127 Specify the velocity of the four notes that will sound when the Preview Mode is set to “SINGLE”
or “CHORD.”
* If “PHRASE” is selected for the Preview Mode parameter, these settings will have no effect.
Scale Tune for Patch Mode
The Fantom-Xa allows you to play the keyboard using temperaments other than equal temperament. The pitch is specified in one-cent units
relative to the equal tempered pitch.
* One-cent is 1/100th of a semitone.
One set of Scale Tune settings can be created in Patch mode. In Performance mode, this can be set for each part of the performance (p. 76).
* In Patch mode, this is valid only for the keyboard part.
• The selected scale applies to MIDI messages received from an external MIDI device.
Scale Tune Switch OFF, ON Turn this on when you wish to use a tuning scale other than equal temperament.
Patch Scale Tune for
C–B
-64– +63 Make scale tune settings for Patch mode.
Parameter Value Explanation
USB Mode
STORAGE, MIDI Selects the mode in which the USB connector will be used.
STORAGE:
Storage mode. Select this if you want to transfer files.
MIDI:
MIDI mode. Select this if you want to exchange MIDI messages with a sequencer or oth-
er program.
* For details on switching the USB mode, refer to
Switching the USB Storage Mode and the MIDI
Mode
(p. 206)
USB-MIDI Thru
OFF, ON When USB Mode is set to “MIDI,” this switch specifies whether MIDI messages received at the
MIDI connector will be retransmitted from the MIDI OUT connector (ON) or not (OFF).
Fantom-Xa_e.book 194 ページ ２００４年１０月２２日 金曜日 午後２時３分