Filter
Top Products
78
Creating a Performance
The Fantom-Xa lets you assign the parameters that will be affected
when you operate the realtime control knobs, assignable switches, D
Beam, pitch bend, or modulation lever. This lets you modify the
sound in a variety of ways by operating the controllers.
1.
Access the PERFORM LAYER screen, and select the
Performance whose settings you wish to modify (p. 67).
2.
Press [F3 (CONTROL)].
The CTRL SETTING screen appears.
fig.CtrlSettingPfm
3.
Press [F1]–[F5] and/or to select the parameter.
4.
Use the VALUE dial or [INC] [DEC] to change the value.
5.
Repeat steps
3
–
5
to set each parameter you want to edit.
6.
Press [WRITE] to save the changes you’ve made.
If you do not wish to save changes, press [EXIT] to return to
the PERFORM LAYER screen.
* Settings for the Solo Synth are saved for system settings. Press [F6
(WRITE)] to execute the write operation.
If you return to the PERFORM LAYER screen without saving,
an “*” will be displayed at the left of the Performance group.
If you turn off the power or select a different sound while the
display indicates “*,” your edited Performance will be lost.
[F1 (KNOB)]
For details, refer to
REALTIME CONTROL Knob Settings
(p. 83)
[F2 (SWITCH)]
For details, refer to
ASSIGNABLE Switch Settings
(p. 84).
[F3 (TEMPO)]
Recommended Tempo
If you want the sequencer tempo to change when you switch
Performances, specify the tempo that will follow this change. This
setting is valid when the Seq Tempo Override parameter is “ON.” In
order to enable this setting, turn on the Tempo Override parameter
(p. 200).
VALUE:
20–250
* This value is specified independently for each performance. This means
that when you switch performances, the tempo setting of the Fantom-
Xa will change.
* The sequencer tempo will be overwritten to the new tempo when you
switch performances.
[F4 (DBEAM)]
For details, refer to
Pad Trigger
(p. 82) and
Assignable
(p. 82).
[F5 (DB SYN)]
For details, refer to
Solo Synth
(p. 81).
You can change controller switch on/off settings for each patch in
the performance.
1.
In the CONTROL SETTING screen, press [F6 (CTRL SW)].
The CONTROL SWITCH screen appears.
fig.CtrlSwPfm
2.
Use [CURSOR] to select the parameter.
3.
Use the VALUE dial or [INC] [DEC] to change the setting.
4.
Repeat steps 2–3 to set each parameter you want to edit.
5.
Press [F6 (EXIT)] to return to the previous screen.
Settings for the Realtime
Controllers and D Beam
Controller
Control Switch Settings
[F6 (CTRL SW)]
Parameter
Value Explanation
PB
OFF,
ON (
✔
)
For each part, specify whether MIDI
Pitch Bend messages will be transmit-
ted.
Mod For each part, specify whether MIDI
Modulation messages will be transmit-
ted.
Hold For each part, you can specify whether
control messages from a pedal connect-
ed to the HOLD PEDAL jacks will be
transmitted.
Ctrl For each part, you can specify whether
control messages from a pedal connect-
ed to the CONTROL PEDAL jacks will
be transmitted.
D Beam Specifies whether each part will be con-
trolled by the D Beam.
Knob 1–4 Specifies whether each part will be con-
trolled by the REALTIME CONTROL
knob 1–4.
Fantom-Xa_e.book 78 ページ ２００４年１０月２２日 金曜日 午後２時３分