Filter
Top Products
114
: High Damp [%], : Low Damp [%]
These parameters set the damping amount of high range and low
range. The tone of the delayed sound becomes darker and lighter
as it feeds back.
: Spread
This parameter sets the pan width of the effect sound. The stereo
image is widest with a value of “50,” and the effect sound of both
channels is output from the center with a value of “0.”
9: DL2: St/Cross Delay (Stereo/Cross Delay)
This is a stereo delay, and can by used as a cross-feedback
delay effect in which the delay sounds cross over between the
left and right by changing the feedback routing.
10: DL3: St.Multitap Delay (Stereo Multitap Delay)
The left and right Multitap Delays have two taps respectively.
Changing the routing of feedback and tap output allows you
to create various patterns of complex effect sounds.
: Mode
The left/right panning of the delay can be modified by changing
the connections of the left and right delay. Be aware that different
sounds must be input to the left and right channels in order for
this parameter to be effective.
: Tap1 Level
This parameter sets the output level of Tap1. Setting a different
level from Tap2 will add a unique touch to a monotonous delay
and feedback.
11: DL4: St.Modulation Delay
(Stereo Modulation Delay)
This stereo delay uses an LFO to sweep the delay time. The
pitch also varies. You will obtain a delay sound with swell and
shimmering.
: L LFO Phase [degree], : R LFO Phase [degree]
“L LFO Phase” and “R LFO Phase” specify the phase difference
between the two LFO’s when they are reset. This allows the pitch
change of the sweep to be set independently for left and right.
12: DL5: St.Dynamic Delay (Stereo Dynamic Delay)
This stereo delay controls the level of delay according to the
input signal level. You can use this as a ducking delay that
applies delay to the sound only when you input signals at a
high velocity or only when the volume level is low.
: Control Target
This parameter selects no level control, delay output control (effect
balance), or feedback amount control.
: Polarity, :Threshold, :Offset, :Attack, :Release
The “Offset” parameter specifies the value for the “Control Target”
parameter (when level control is not being applied), expressed as a
ratio relative to the parameter setting. The parameter setting will
be the “Wet/Dry” value if “Control Target”=“Out,” or the “Feed-
back” value if “Control Target”=“FB.”
When “Polarity” is “+”, the “Control Target” value is obtained by
multiplying the parameter value by the “Offset” value (if the input
level is below “Threshold”), or will equal the parameter value if
the input level exceeds the threshold.
When “Polarity” is “–”, the Control Target value will equal the
parameter value if the input level is below “Threshold”, or is
obtained by multiplying the parameter value by the “Offset” value
if the input level exceeds “Threshold.”
HiDamp (High Damp [%]).................0...100 Sets the damping amount in the high
range
LoDamp (Low Damp [%]).................0...100 Sets the damping amount in the low
range
Spread (Spread).................................0...50 Sets the width of the stereo image of
the effect sound
Mix (Wet/Dry)...............Dry, 1:99...99:1, Wet Sets the balance between the effect
and dry sounds
Mode (Stereo/Cross)............. Stereo, Cross Switches between stereo delay and
cross-feedback delay
LTime (L Delay Time [msec])....... 0...680ms Sets the delay time for the left channel
RTime (R Delay Time [msec])......0...680ms Sets the delay time for the right channel
LFback (L Feedback)................–100...+100 Sets the feedback amount for the left
channel
RFback (R Feedback)...............–100...+100 Sets the feedback amount for the right
channel
HiDamp (High Damp [%]).................0...100 Sets the damping amount in the high
range
LoDamp (Low Damp [%]).................0...100 Sets the damping amount in the low
range
Spread (Spread)...........................–50...+50 Sets the width of the stereo image of
the effect sound
Mix (Wet/Dry)...............Dry, 1:99...99:1, Wet Sets the balance between the effect
and dry sounds
Mode (Mode)................... Normal, X.Fback,
X.Pan1, X.Pan2
Switches the left and right delay routing
T1Time (Tap1 Time [msec])......... 0...680ms Sets the Tap1 delay time
T2Time (Tap2 Time [msec])......... 0...680ms Sets the Tap2 delay time
T1Lvl (Tap1 Level)............................0...100 Sets the Tap1 output level
Fdback (Feedback)...................–100...+100 Sets the Tap2 feedback amount
HiDamp (High Damp [%]).................0...100 Sets the damping amount in the high
range
LoDamp (Low Damp [%]).................0...100 Sets the damping amount in the low
range
Spread (Spread).......................–100...+100 Sets the width of the stereo image of
the effect sound
Mix (Wet/Dry)...............Dry, 1:99...99:1, Wet Sets the balance between the effect
and dry sounds
LFO (LFO Waveform).................... TRI, SIN Selects LFO Waveform
Shape (LFO Shape) .................–100...+100 Determines how much the LFO wave-
form is changed
*Speed (LFO Frequency [Hz])..0.02...20.0Hz Sets the LFO speed
LPhase (L LFO Phase [degree])–180...+180 Sets the phase obtained when the left
LFO is reset
RPhase(R LFO Phase [degree])–180...+180 Sets the phase obtained when the right
LFO is reset
*LDepth (L Depth)..............................0...200 Sets the depth of the left LFO modula-
tion
*RDepth (R Depth).............................0...200 Sets the depth of the right LFO modula-
tion
LTime (L Delay Time [msec])............0...500 Sets the delay time for the left channel
RTime (R Delay Time [msec])...........0...500 Sets the delay time for the right channel
LFback (L Feedback)................–100...+100 Sets the feedback amount of left delay
RFback (R Feedback)...............–100...+100 Sets the feedback amount of right delay
Mix (Wet/Dry).................. –Wet...–1:99, Dry,
1:99...Wet
Sets the balance between the effect
and dry sounds
Contrl (Control Target)..........None, Out, FB Selects from no control, output, and
feedback
Polrty (Polarity)......................................+, – Reverses level control
Thrshl (Threshold)............................0...100 Sets the level to which the effect is
applied
Offset (Offset)...................................0...100 Sets the offset of level control
Attack (Attack)..................................1...100 Sets the attack time of level control
Relse (Release)................................1...100 Sets the release time of level control
LTime (L Delay Time [msec])....... 0...680ms Sets the delay time for the left channel
RTime (R Delay Time [msec])......0...680ms Sets the delay time for the right channel
Fdback (Feedback)...................–100...+100 Sets the feedback amount
HiDamp (High Damp [%]).................0...100 Sets the damping amount in the high
range
LoDamp (Low Damp [%]).................0...100 Sets the damping amount in the low
range
Spread (Spread).......................–100...+100 Sets the width of the stereo image of
the effect sound
Mix (Wet/Dry)...............Dry, 1:99...99:1, Wet Sets the balance between the effect
and dry sounds