Filter
Top Products
129
Effect/Parameter List
65: GATED REV (GATED REVERB)
This is a special type of reverb in which the reverberant sound is cut
off before its natural length.
66: OVDRV
→
CHO
(OVERDRIVE
→
CHORUS)
This effect connects an overdrive and a chorus in series.
67: OVDRV
→
FLNGR
(OVERDRIVE
→
FLANGER)
This effect connects an overdrive and a flanger in series.
68: OVDRV
→
DELAY
(OVERDRIVE
→
DELAY)
This effect connects an overdrive and a delay in series.
69: DIST
→
CHORUS
(DISTORTION
→
CHORUS)
The parameters are essentially the same as in “66: OVERDRIVE
→
CHORUS,” with the exception of the following two.
Overdrive Drive
→
Distortion Drive
Overdrive Pan
→
Distortion Pan
70: DIST
→
FLANGR
(DISTORTION
→
FLANGER)
The parameters are essentially the same as in “67: OVERDRIVE
→
FLANGER,” with the exception of the following two.
Overdrive Drive
→
Distortion Drive
Overdrive Pan
→
Distortion Pan
Assignable Parameters
MFX Control Balance
Parameter Value Description
Type NORMAL,
REVERSE,
SWEEP1,
SWEEP2
Type of reverb
NORMAL
: conventional gated reverb
REVERSE
: backwards reverb
SWEEP1
: the reverberant sound
moves from right to left
SWEEP2
: the reverberant sound
moves from left to right
Pre Delay 0.0–100.0 ms Adjusts the delay time from the direct
sound until the reverb sound is heard.
Gate Time 5–500 ms Adjusts the time from when the reverb
is heard until it disappears.
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Balance D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the reverb sound (W)
Level 0–127 Output Level
Assignable Parameters
MFX Control Chorus Bal, Cho Rate, Chorus Depth, Overdrive Drive
Parameter Value Description
Overdrive
Drive
0–127 Degree of distortion
Also changes the volume.
Overdrive Pan L64–63R Stereo location of the overdrive sound
Chorus PreDly 0.0–100.0 ms Adjusts the delay time from the direct
sound until the chorus sound is heard.
Rate Mode Hz, note When this is set to “note,” the effect is
synchronized with the tempo.
Cho Rate(Hz) 0.05–10.00
Hz
Frequency of modulation (Hz)
Cho Rate
()
note (*1) Frequency of modulation (note)
Chorus Depth 0–127 Depth of modulation
Chorus Bal D100:0W–
D0:100W
Adjusts the volume balance between the
sound that is sent through the chorus
(W) and the sound that is not sent
through the chorus (D).
Level 0–127 Output Level
Assignable Parameters
MFX Control Flngr Bal, Fln Rate, Flngr Depth, Flngr Feedback,
Overdrive Drive
Parameter Value Description
Overdrive
Drive
0–127 Degree of distortion
Also changes the volume.
Overdrive Pan L64–63R Stereo location of the overdrive sound
Flngr PreDly 0.0–100.0 ms Adjusts the delay time from when the
direct sound begins until the flanger
sound is heard.
Flngr Mode Hz, note When this is set to “note,” the effect is
synchronized with the tempo.
Fln Rate(Hz) 0.05–10.00
Hz
Frequency of modulation (Hz)
Fln Rate( )
note (*1) Frequency of modulation (note)
Flngr Depth 0–127 Depth of modulation
Flngr Feedback -98– +98 % Adjusts the proportion of the flanger
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Flngr Bal D100:0W–
D0:100W
Adjusts the volume balance between the
sound that is sent through the flanger
(W) and the sound that is not sent
through the flanger (D).
Level 0–127 Output Level
Assignable Parameters
MFX Control Delay Bal, Overdrive Drive
Parameter Value Description
Overdrive
Drive
0–127 Degree of distortion
Also changes the volume.
Overdrive Pan L64–63R Stereo location of the overdrive sound
Delay Mode ms, note When this is set to “note,” the effect is
synchronized with the tempo.
Delay (ms) 1–2600 ms Adjusts the delay time from the direct
sound until the delay sound is heard.
(Hz)
Delay ( )
note (*1) Adjusts the delay time from the direct
sound until the delay sound is heard.
(note)
Delay Feedback -98– +98 % Adjusts the proportion of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Delay HF
Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the effect will be cut.
If you do not want to cut the high
frequencies, set this parameter to
BYPASS.
Delay Bal D100:0W–
D0:100W
Adjusts the volume balance between the
sound that is sent through the delay (W)
and the sound that is not sent through
the delay (D).
Level 0–127 Output Level
Parameter Value Description
RD-700SX_e.book 129 ページ ２００６年３月２３日 木曜日 午後２時５２分