Filter
Top Products
140
Effect/Parameter List
108: *FBK P.SFT (FEEDBACK PITCH
SHIFTER)
This pitch shifter allows the pitch shifted sound to be fed back into the
effect.
109: *REVERB
The Reverb effect adds reverberation to the sound, simulating an
acoustic space.
110: *GATE REV (GATED REVERB)
Gate Reverb is a special type of reverb in which the reverberant sound
is cut off before its natural length.
Assignable Parameters
MFX Control Balance, Coarse, Feedback
Parameter Value Description
Mode 1, 2, 3, 4, 5 Higher settings of this parameter will
result in slower response, but steadier
pitch.
Coarse -24– +12
semitone
Adjust the pitch of the pitch shifted
sound in semitone steps (-2–+1 octaves).
Fine -100– +100
cent
Make fine adjustments to the pitch of
the pitch shifted sound in 2-cent steps
(one cent is 1/100th of a semi tone).
Pre Delay 0.0–500.0 ms Adjust the time delay from when the
direct sound begins until the pitch
shifted sound is heard.
Feedback -98– +98% Adjust the proportion (%) of the
processed sound that is fed back into the
effect. Negative (-) settings will invert
the phase.
Pan L64–0–63R Adjust the stereo location of the pitch
shifted sound. L64 is far left, 0 is center,
and 63R is far right.
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the pitch shift sound.
With a setting of D100:0W only the
direct sound will be output, and with a
setting of D0:100W only the pitch shift
sound will be output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Time, Type, Balance
Parameter Value Description
Type ROOM1,
ROOM2,
STAGE1,
STAGE2,
HALL1,
HALL2
Select the type of Reverb effect.
ROOM1
: dense reverb with short
decay
ROOM2
: sparse reverb with short
decay
STAGE1
: reverb with greater late
reverberation
STAGE2
: reverb with strong early
reflections
HALL1
: reverb with clear
reverberance
HALL2
: reverb with rich
reverberance
Pre Delay 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the reverb
sound is heard.
Time 0–127 Adjust the time length of reverberation.
HF Damp 200–8000 Hz,
BYPASS
Adjust the frequency above which the
reverberant sound will be cut. As the
frequency is set lower, more of the high
frequencies will be cut, resulting in a
softer and more muted reverberance. If
you do not want the high frequencies to
be cut, set this parameter to BYPASS.
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the reverb sound.
With a setting of D100:0W only the
direct sound will be output, and with a
setting of D0:100W only the reverb
sound will be output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Balance
Parameter Value Description
Type NORMAL,
REVERSE,
SWEEP1,
SWEEP2
Select the type of reverb.
NORMAL
: conventional gate reverb
REVERSE
: backwards reverb
SWEEP1
: the reverberant sound
moves from right to left
SWEEP2
: the reverberant sound
moves from left to right
Pre Delay 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the reverb
sound is heard.
Time 5–500 ms Adjust the time from when the reverb is
heard until when it disappears.
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the reverb sound.
With a setting of D100:0W only the
direct sound will be output, and with a
setting of D0:100W only the reverb
sound will be output.
Level 0–127 Adjust the output level.
Parameter Value Description
RD-700SX_e.book 140 ページ ２００６年３月２３日 木曜日 午後２時５２分