Filter
Top Products
138
Effect/Parameter List
103: *MOD DELAY (MODULATION
DELAY)
This effect adds modulation to the delayed sound, producing an effect
similar to a flanger.
104: *TRIPLE DLY (TRIPLE TAP DELAY)
The Triple Tap Delay produces three delay sounds; center, left and
right.
Delay C, Delay L and Delay R parameters can be set as a note-value of
a tempo. In this case, specify the value of the desired note.
105: *QUAD.DELAY (QUADRUPLE TAP
DELAY)
The Quadruple Tap Delay has four delays.
The stereo location of each delay sound is as follows.
HF Damp 200–8000 Hz,
BYPASS
Adjust the frequency above which
sound fed back to the effect will be cut.
If you do not want to cut the high
frequencies of the feedback, set this
parameter to BYPASS.
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the delay sound. With
a setting of D100:0W only the direct
sound will be output, and with a setting
of D0:100W only the delay sound will be
output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Rate, Balance
Parameter Value Description
Feedback mode NORMAL,
CROSS
Select the way in which delay sound is
fed back into the effect.
NORMAL
: The left delay sound will
be fed back into the left delay, and the
right delay sound into the right delay.
CROSS
: The left delay sound will be
fed back into the right delay, and the
right delay sound into the left delay.
Delay Left 0.1–500.0 ms Adjust the time from the direct sound
until when the left delay sound is heard.
Delay Right 0.1–500.0 ms Adjust the time from the direct sound
until when the right delay sound is
heard.
Feedback -98– +98% Adjust the proportion (%) of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
HF Damp 200–8000 Hz,
BYPASS
Adjust the frequency above which
sound fed back to the effect will be cut.
If you do not want to cut the high
frequencies of the feedback, set this
parameter to BYPASS.
Rate 0.05–10.00
Hz
Adjust the speed of the modulation.
Depth 0–127 Adjust the depth of the modulation.
Phase 0–180 degree Adjust the spatial spread of the sound.
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the modulation delay
sound. With a setting of D100:0W only
the direct sound will be output, and
with a setting of D0:100W only the
modulation delay sound will be output.
Parameter Value Description
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Balance
Parameter Value Description
Dly Left 200–1000 ms,
note (*2)
Adjust the time delay from the direct
sound until when the left delay sound is
heard.
Dly Right 200–1000 ms,
note (*2)
Adjust the time delay from the direct
sound until when the right delay sound
is heard.
Dly Center 200–1000 ms,
note (*2)
Adjust the time delay from the direct
sound until when the center delay
sound is heard.
Feedback -98– +98% Adjust the proportion (%) of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
HF Damp 200–8000 Hz,
BYPASS
Adjust the frequency above which
sound fed back to the effect will be cut.
If you do not want to cut the high
frequencies of the feedback, set this
parameter to BYPASS.
Left Level 0–127 Adjust the volume of the left delay
sound.
Right Level 0–127 Adjust the volume of the right delay
sound.
Center Level 0–127 Adjust the volume of the center delay
sound.
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the delay sound. With
a setting of D100:0W only the direct
sound will be output, and with a setting
of D0:100W only the delay sound will be
output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Balance
Parameter Value Description
Dly1 Time 200–1000 ms,
note
Adjust the time delay from the direct
sound until when delay 1 sound is
heard.
Dly2 Time 200–1000 ms,
note
Adjust the time delay from the direct
sound until when delay 2 sound is
heard.
Parameter Value Description
RD-700SX_e.book 138 ページ ２００６年３月２３日 木曜日 午後２時５２分