Filter
Top Products
141
Effect/Parameter List
111: *OVDRV
→
CHO (OVERDRIVE
→
CHORUS)
This effect connects an overdrive and a chorus in series.
112: *OVDRV
→
FLN
(OVERDRIVE
→
FLANGER)
This effect connects an overdrive and a flanger in series.
113: *OVDRV
→
DLY (OVERDRIVE
→
DELAY)
This effect connects an overdrive and a delay in series.
114: *DIST
→
CHO (DISTORTION
→
CHORUS)
This effect connects distortion and chorus in series. The parameters
are essentially the same as “111: OD
→
CHORUS,” with the exception
of the following two.
OD Drive
→
Dst Drive (Specify the amount of distortion.)
OD Pan
→
Dist Pan (Specify the stereo location of the distortion
sound.)
115: *DIST
→
FLNGR (DISTORTION
→
FLANGER)
This effect connects distortion and flanger in series. The parameters
are essentially the same as in “112: OD
→
FLANGER,” with the
exception of the following two.
OD Drive
→
Dst Drive (Specify the amount of distortion.)
OD Pan
→
Dist Pan (Specify the stereo location of the distortion
sound.)
116: *DIST
→
DELAY (DISTORTION
→
DELAY)
This effect connects distortion and delay in series. The parameters are
essentially the same as in “113: OD
→
DELAY,” with the exception of
the following two.
OD Drive
→
Dst Drive (Specify the amount of distortion.)
OD Pan
→
Dist Pan (Specify the stereo location of the
distortion sound.)
Assignable Parameters
MFX Control Chorus Bal, Chorus Rate, OD Drive
Parameter Value Description
OD Drive 0–127 Adjust the degree of overdrive
distortion. The volume will change
together with the degree of distortion.
OD Pan L64–0–63R Adjust the stereo location of the
overdrive sound. L64 is far left, 0 is
center, and 63R is far right.
Chorus PreDly 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the chorus
sound is heard.
Chorus Rate 0.05–10.00
Hz
Adjust the modulation speed of the
chorus effect.
Chorus Depth 0–127 Adjust the modulation depth of the
chorus effect.
Chorus Bal D100:0W–
D0:100W
Adjust the volume balance between the
overdrive sound that is sent through the
chorus and the overdrive sound that is
not sent through the chorus. With a
setting of “D100:0W,” only the
overdrive sound will be output. With a
setting of “D0:100W,” only the
overdrive sound that is sent through the
chorus will be output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Flngr Bal, Flngr Rate, OD Drive
Parameter Value Description
OD Drive 0–127 Adjust the degree of overdrive
distortion. The volume will change
together with the degree of distortion.
OD Pan L64–0–63R Adjust the stereo location of the
overdrive sound. L64 is far left, 0 is
center, and 63R is far right.
Flngr PreDly 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the flanger
sound is heard.
Flngr Rate 0.05–10.00
Hz
Adjust the modulation speed of the
flanger effect.
Flngr Depth 0–127 Adjust the modulation depth of the
flanger effect.
Flngr Fbk -98– +98% Adjust the proportion (%) of the flanger
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Flngr Bal D100:0W–
D0:100W
Adjust the volume balance between the
overdrive sound that is sent through the
flanger and the overdrive sound that is
not sent through the flanger. With a
setting of “D100:0W,” only the
overdrive sound will be output. With a
setting of “D0:100W,” only the
overdrive sound that is sent through the
flanger will be output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Delay Bal, OD Drive
Parameter Value Description
OD Drive 0–127 Adjust the degree of overdrive
distortion. The volume will change
together with the degree of distortion.
OD Pan L64–0–63R Adjust the stereo location of the
overdrive sound. L64 is far left, 0 is
center, and 63R is far right.
Delay Time 0.1–500.0 ms Adjust the time delay from when the
direct sound begins until the delay
sound is heard.
Delay Feedback -98– +98% Adjust the proportion (%) of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Delay HF
Damp
200–8000 Hz,
BYPASS
Adjust the frequency above which
delayed sound fed back to the effect will
be cut. If you do not want to cut the high
frequencies of the feedback, set this
parameter to BYPASS.
Delay Bal D100:0W–
D0:100W
Adjust the volume balance between the
overdrive sound that is sent through the
delay and the overdrive sound that is
not sent through the delay. With a
setting of “D100:0W,” only the
overdrive sound will be output. With a
setting of “D0:100W,” only the
overdrive sound that is sent through the
delay will be output.
Level 0–127 Adjust the output level.
RD-700SX_e.book 141 ページ ２００６年３月２３日 木曜日 午後２時５２分