Filter
Top Products
142
Effect/Parameter List
117: *ENH
→
CHORUS (ENHANCER
→
CHORUS)
This effect connects an enhancer and a chorus in series.
118: *ENH
→
FLANGR (ENHANCER
→
CHORUS)
This effect connects an enhancer and a flanger in series.
119: *ENH
→
DELAY (ENHANCER
→
DELAY)
This effect connects an enhancer and a delay in series.
120: *CHO
→
DELAY (CHORUS
→
DELAY)
This effect connects a chorus and a delay unit in series.
Assignable Parameters
MFX Control Chorus Bal, Chorus Rate, Enhancer Sens
Parameter Value Description
Enhancer Sens 0–127 Adjust the sensitivity of the enhancer.
Enhancer Mix 0–127 Adjust the ratio with which the
overtones generated by the enhancer
are combined with the direct sound.
Chorus PreDly 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the chorus
sound is heard.
Chorus Rate 0.05–10.00
Hz
Adjust the modulation speed of the
chorus effect.
Chorus Depth 0–127 Adjust the modulation depth of the
chorus effect.
Chorus Bal D100:0W–
D0:100W
Adjust the volume balance between the
enhancer sound that is sent through the
chorus and the enhancer sound that is
not sent through the chorus. With a
setting of “D100:0W,” only the enhancer
sound will be output. With a setting of
“D0:100W,” only the enhancer sound
that is sent through the chorus will be
output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Flngr Bal, Flngr Rate, Enhancer Sens
Parameter Value Description
Enhancer Sens 0–127 Adjust the sensitivity of the enhancer.
Enhancer Mix 0–127 Adjust the ratio with which the
overtones generated by the enhancer
are combined with the direct sound.
Flngr PreDly 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the flanger
sound is heard.
Flngr Rate 0.05–10.00
Hz
Adjust the modulation speed of the
flanger effect.
Flngr Depth 0–127 Adjust the modulation depth of the
flanger effect.
Flngr Fbk -98– +98% Adjust the proportion (%) of the flanger
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Flngr Bal D100:0W–
D0:100W
Adjust the volume balance between the
enhancer sound that is sent through the
flanger and the enhancer sound that is
not sent through the flanger. With a
setting of “D100:0W,” only the enhancer
sound will be output. With a setting of
“D0:100W,” only the enhancer sound
that is sent through the flanger will be
output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Delay Bal, Enhancer Sens
Parameter Value Description
Enhancer Sens 0–127 Adjust the sensitivity of the enhancer.
Enhancer Mix 0–127 Adjust the ratio with which the
overtones generated by the enhancer
are combined with the direct sound.
Delay Time 0.1–500.0 ms Adjust the time delay from when the
direct sound begins until the delay
sound is heard.
Delay Feedback -98– +98% Adjust the proportion (%) of the delay
sound that is fed back into the delay
input. Negative (-) settings will invert
the phase.
Delay HF
Damp
200–8000 Hz,
BYPASS
Adjust the frequency above which
delayed sound fed back to the delay
input will be cut. If you do not want to
cut the high frequencies of the delay
feedback, set this parameter to BYPASS.
Delay Bal D100:0W–
D0:100W
Adjust the volume balance between the
enhancer sound that is sent through the
delay and the enhancer sound that is not
sent through the delay. With a setting of
“D100:0W,” only the enhancer sound
will be output. With a setting of
“D0:100W,” only the enhancer sound
that is sent through the delay will be
output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Chorus Bal, Delay Bal
Parameter Value Description
Chorus PreDly 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the chorus
sound is heard.
Chorus Rate 0.05–10.00
Hz
Adjust the modulation speed of the
chorus effect.
Chorus Depth 0–127 Adjust the modulation depth of the
chorus effect.
Chorus Bal D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the chorus sound.
With a setting of “D100:0W,” only the
direct sound will be output. With a
setting of “D0:100W,” only the chorus
sound will be output.
Delay Time 0.1–500.0 ms Adjust the time delay from when the
direct sound begins until the delay
sound is heard.
Delay Feedback -98– +98% Adjust the proportion (%) of the delay
sound that is fed back into the delay
input. Negative (-) settings will invert
the phase.
Delay HF
Damp
200–8000 Hz,
BYPASS
Adjust the frequency above which
delayed sound fed back to the delay
input will be cut. If you do not want to
cut the high frequencies of the feedback,
set this parameter to BYPASS.
Delay Bal D100:0W–
D0:100W
Adjust the volume balance between the
chorus sound that is sent through the
delay and the chorus sound that is not
sent through the delay. With a setting of
“D100:0W,” only the chorus sound will
be output. With a setting of “D0:100W,”
only the chorus sound that is sent
through the delay will be output.
Level 0–127 Adjust the output level.
RD-700SX_e.book 142 ページ ２００６年３月２３日 木曜日 午後２時５２分