Filter
Top Products
136
Effect/Parameter List
96: *HEXA-CHO (HEXA-CHORUS)
Hexa-chorus uses a six-phase chorus (six layers of chorused sound) to
give richness and spatial spread to the sound.
97: *TREMOL CHO (TREMOLO CHORUS)
Tremolo Chorus is a chorus effect with added Tremolo (cyclic
modulation of volume).
98: *SPACE-D
Space-D is a multiple chorus that applies two-phase modulation in
stereo. It gives no impression of modulation, but produces a
transparent chorus effect.
99: *STEREO CHO (STEREO CHORUS)
This is a stereo chorus. A filter is provided so that you can adjust the
timbre of the chorus sound.
Pan L64–0–63R Adjust the stereo location of the output
sound. L64 is far left, 0 is center, and 63R
is far right.
Post Gain 0, +6, +12,
+18 dB
Adjust the output gain.
Low Gain -15– +15 dB Adjust the low frequency gain.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB Adjust the high frequency gain.
Positive (+) settings will emphasize
(boost) the high frequency range.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Rate, Balance
Parameter Value Description
Pre Delay 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the chorus
sound is heard.
Rate 0.05–10.00
Hz
Adjust the rate of modulation.
Depth 0–127 Adjust the depth of modulation.
Pre Delay
Deviat
0–20 Pre Delay determines the time from
when the direct sound begins until the
processed sound is heard. Pre Delay
Deviation adjusts the differences in Pre
Delay between each chorus sound.
Depth
Deviation
-20– +20 Adjust the difference in modulation
depth between each chorus sound. The
shift between the start of each of the
chorus sounds increases as the value is
increased.
Pan Deviation 0–20 Adjust the difference in stereo location
between each chorus sound. With a
setting of 0, all chorus sounds will be in
the center. With a setting of 20, each
chorus sound will be spaced at 60
degree intervals relative to the center.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the chorus sound.
With a setting of D100:0W only the
direct sound will be output, and with a
setting of D0:100W only the chorus
sound will be output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Chorus Rate, Treml Rate, Balance
Parameter Value Description
Pre Delay 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the chorus
sound is heard.
Chorus Rate 0.05–10.00
Hz
Adjust the modulation speed of the
chorus effect.
Chorus Depth 0–127 Adjust the modulation depth of the
chorus effect.
Treml Rate 0.05–10.00
Hz
Adjust the modulation speed of the
tremolo effect.
Parameter Value Description
Treml
Separation
0–127 Adjust the spread of the tremolo effect.
Treml Phase 0–180 degree Adjust the spread of the tremolo effect.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the tremolo chorus
sound. With a setting of D100:0W only
the direct sound will be output, and
with a setting of D0:100W only the
tremolo chorus sound will be output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Rate, Balance
Parameter Value Description
Pre Delay 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the processed
sound is heard.
Rate 0.05–10.00
Hz
Adjust the rate of modulation.
Depth 0–127 Adjust the depth of modulation.
Phase 0–180 degree Adjust the spatial spread of the sound.
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the chorus sound.
With a setting of D100:0W only the
direct sound will be output, and with a
setting of D0:100W only the chorus
sound will be output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Rate, Balance
Parameter Value Description
Filter Type OFF,
LPF,
HPF
Select the type of filter.
OFF
: a filter will not be used
LPF
: cut the frequency range above
the cutoff frequency
HPF
: cut the frequency range below
the cutoff frequency
Cutoff Freq 200–8000 Hz Adjust the basic frequency of the filter.
Pre Delay 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the processed
sound is heard.
Rate 0.05–10.00
Hz
Adjust the rate of modulation.
Depth 0–127 Adjust the depth of modulation.
Phase 0–180 degree Adjust the spatial spread of the sound.
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
Parameter Value Description
RD-700SX_e.book 136 ページ ２００６年３月２３日 木曜日 午後２時５２分