Filter
Top Products
130
Effect/Parameter List
71: DIST
→
DELAY (DISTORTION
→
DELAY)
The parameters are essentially the same as in “68:
OVERDRIVE
→
DELAY,” with the exception of the following two.
Overdrive Drive
→
Distortion Drive
Overdrive Pan
→
Distortion Pan
72: ENH
→
CHORUS
(ENHANCER
→
CHORUS)
This effect connects an enhancer and a chorus in series.
73: ENH
→
FLANGER
(ENHANCER
→
FLANGER)
This effect connects an enhancer and a flanger in series.
74: ENH
→
DELAY (ENHANCER
→
DELAY)
This effect connects an enhancer and a delay in series.
75: CHO
→
DELAY (CHORUS
→
DELAY)
This effect connects a chorus and a delay in series.
Assignable Parameters
MFX Control Chorus Bal, Chorus Depth, Cho Rate, Enhancer Sens
Parameter Value Description
Enhancer Sens 0–127 Sensitivity of the enhancer
Enhancer Mix 0–127 Level of the overtones generated by the
enhancer
Chorus PreDly 0.0–100.0 ms Adjusts the delay time from the direct
sound until the chorus sound is heard.
Rate Mode Hz, note When this is set to “note,” the effect is
synchronized with the tempo.
Cho Rate(Hz) 0.05–10.00
Hz
Frequency of modulation (Hz)
Cho Rate
()
note (*1) Frequency of modulation (note)
Chorus Depth 0–127 Depth of modulation
Chorus Bal D100:0W–
D0:100W
Adjusts the volume balance between the
sound that is sent through the chorus
(W) and the sound that is not sent
through the chorus (D).
Level 0–127 Output Level
Assignable Parameters
MFX Control Flngr Bal, Fln Rate, Flngr Depth, Flngr Feedback,
Enhancer Sens
Parameter Value Description
Enhancer Sens 0–127 Sensitivity of the enhancer
Enhancer Mix 0–127 Level of the overtones generated by the
enhancer
Flngr PreDly 0.0–100.0 ms Adjusts the delay time from when the
direct sound begins until the flanger
sound is heard.
Flngr Mode Hz, note When this is set to “note,” the effect is
synchronized with the tempo.
Fln Rate(Hz) 0.05–10.00
Hz
Frequency of modulation (Hz)
Fln Rate( )
note (*1) Frequency of modulation (note)
Flngr Depth 0–127 Depth of modulation
Flngr Feedback -98– +98 % Adjusts the proportion of the flanger
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Flngr Bal D100:0W–
D0:100W
Adjusts the volume balance between the
sound that is sent through the flanger
(W) and the sound that is not sent
through the flanger (D).
Level 0–127 Output Level
Assignable Parameters
MFX Control Delay Bal, Enhancer Sens
Parameter Value Description
Enhancer Sens 0–127 Sensitivity of the enhancer
Enhancer Mix 0–127 Level of the overtones generated by the
enhancer
Delay Mode ms, note When this is set to “note,” the effect is
synchronized with the tempo.
Delay (ms) 1–2600 ms Adjusts the delay time from the direct
sound until the delay sound is heard.
(Hz)
Delay ( )
note (*1) Adjusts the delay time from the direct
sound until the delay sound is heard.
(note)
Delay Feedback -98– +98 % Adjusts the proportion of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Delay HF
Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the effect will be cut.
If you do not want to cut the high
frequencies, set this parameter to
BYPASS.
Delay Bal D100:0W–
D0:100W
Adjusts the volume balance between the
sound that is sent through the delay (W)
and the sound that is not sent through
the delay (D).
Level 0–127 Output Level
Assignable Parameters
MFX Control Delay Bal, Chorus Bal, Chorus Depth, Cho Rate
Parameter Value Description
Chorus PreDly 0.0–100.0 ms Adjusts the delay time from the direct
sound until the chorus sound is heard.
Rate Mode Hz, note When this is set to “note,” the effect is
synchronized with the tempo.
Cho Rate(Hz) 0.05–10.00
Hz
Frequency of modulation (Hz)
Cho Rate
()
note (*1) Frequency of modulation (note)
Chorus Depth 0–127 Depth of modulation
Chorus Bal D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the chorus sound (W)
Delay Mode ms, note When this is set to “note,” the effect is
synchronized with the tempo.
Delay (ms) 1–2600 ms Adjusts the delay time from the direct
sound until the delay sound is heard.
(Hz)
Delay ( )
note (*1) Adjusts the delay time from the direct
sound until the delay sound is heard.
(note)
Delay Feedback -98– +98 % Adjusts the proportion of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Delay HF
Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the effect will be cut.
If you do not want to cut the high
frequencies, set this parameter to
BYPASS.
RD-700SX_e.book 130 ページ ２００６年３月２３日 木曜日 午後２時５２分