Filter
Top Products
137
Effect/Parameter List
100: *ST.FLANGER (STEREO FLANGER)
This is a stereo flanger. (The LFO has the same phase for left and
right.) It produces a metallic resonance that rises and falls like a jet
airplane taking off or landing. A filter is provided so that you can
adjust the timbre of the flanged sound.
101: *STEP FLNGR (STEP FLANGER)
The Step Flanger effect is a flanger in which the flanger pitch changes
in steps.
102: *STEREO DLY (STEREO DELAY)
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the chorus sound.
With a setting of D100:0W only the
direct sound will be output, and with a
setting of D0:100W only the chorus
sound will be output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Rate, Feedback, Balance
Parameter Value Description
Filter Type OFF,
LPF,
HPF
Select the type of filter.
OFF
: a filter will not be used
LPF
: cut the frequency range above
the cutoff frequency
HPF
: cut the frequency range below
the cutoff frequency
Cutoff Freq 200–8000 Hz Adjust the basic frequency of the filter.
Pre Delay 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the flanger
sound is heard.
Rate 0.05–10.00
Hz
Adjust the rate of modulation.
Depth 0–127 Adjust the depth of modulation.
Phase 0–180 degree Adjust the spatial spread of the sound.
Feedback -98– +98% Adjust the proportion (%) of the
processed sound that is returned (fed
back) into the input. Positive (+) settings
will return the sound in phase, and
negative (-) settings will return the
sound in reverse phase.
The effect becomes more prominent as
the value is increased.
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the flanger sound.
With a setting of D100:0W only the
direct sound will be output, and with a
setting of D0:100W only the flanger
sound will be output.
Level 0–127 Adjust the output level.
Parameter Value Description
Assignable Parameters
MFX Control Step Rate, Feedback, Balance
Parameter Value Description
Pre Delay 0.0–100.0 ms Adjust the time delay from when the
direct sound begins until the flanger
sound is heard.
Rate 0.05–10.00
Hz
Adjust the rate of modulation.
Depth 0–127 Adjust the depth of modulation.
Feedback -98– +98% Adjust the proportion (%) of the flanger
sound that is returned (fed back) into
the input. Negative (-) settings will
invert the phase.
The effect becomes more prominent as
the value is increased.
Step Rate 0.10–20.00
Hz, note (*2)
Adjust the rate (period) of pitch change.
Step Rate parameter can be set as a note-
value of a tempo. In this case, specify the
value of the desired note.
Phase 0–180 degree Adjust the spatial spread of the sound.
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the flanger sound.
With a setting of D100:0W only the
direct sound will be output, and with a
setting of D0:100W only the chorus
sound will be output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Balance
Parameter Value Description
Feedback mode NORMAL,
CROSS
Select the way in which delay sound is
fed back into the effect.
NORMAL
: The left delay sound will
be fed back into the left delay, and the
right delay sound into the right delay.
CROSS
: The left delay sound will be
fed back into the right delay, and the
right delay sound into the left delay.
Delay Left 0.1–500.0 ms Adjust the time from the direct sound
until when the left delay sound is heard.
Delay Right 0.1–500.0 ms Adjust the time from the direct sound
until when the right delay sound is
heard.
Phase Left NORMAL,
INVERT
Select the phase of the left delay sound.
NORMAL
: Phase is not changed.
INVERT
: Phase is inverted.
Phase Right NORMAL,
INVERT
Select the phase of the right delay
sound.
NORMAL
: Phase is not changed.
INVERT
: Phase is inverted.
Feedback -98– +98% Adjust the proportion (%) of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
RD-700SX_e.book 137 ページ ２００６年３月２３日 木曜日 午後２時５２分