Filter
Top Products
139
Effect/Parameter List
Delay 1–4 parameters can be set as a note-value of a tempo. In this
case, specify the value of the desired note.
106: *T-CTRL DLY (TIME CONTROL
DELAY)
When the Effects MFX Control (p. 87) setting in Edit mode set to
“Delay,” you can use MULTI EFFECTS [CONTROL] knob to make
changes in the delay time and pitch in real time.
Lengthening the delay will lower the pitch, and shortening it will raise
the pitch.
107: *2V PCH SFT (2 VOICE PITCH
SHIFTER)
A Pitch Shifter shifts the pitch of the direct sound. This 2-voice pitch
shifter has two pitch shifters, and can add two pitch shifted sounds to
the direct sound.
Dly3 Time 200–1000 ms,
note
Adjust the time delay from the direct
sound until when delay 3 sound is
heard.
Dly4 Time 200–1000 ms,
note
Adjust the time delay from the direct
sound until when delay 4 sound is
heard.
Level 1 0–127 Adjust the volume of delay 1 sound.
Level 2 0–127 Adjust the volume of delay 2 sound.
Level 3 0–127 Adjust the volume of delay 3 sound.
Level 4 0–127 Adjust the volume of delay 4 sound.
Feedback -98– +98% Adjust the proportion (%) of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
HF Damp 200–8000 Hz,
BYPASS
Adjust the frequency above which
sound fed back to the effect will be cut.
If you do not want to cut the high
frequencies of the feedback, set this
parameter to BYPASS.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the delay sound. With
a setting of D100:0W only the direct
sound will be output, and with a setting
of D0:100W only the delay sound will be
output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Delay, Balance
Parameter Value Description
Delay 200–1000 ms Adjust the time delay from the direct
sound until when each delay sound is
heard.
Feedback -98– +98% Adjust the proportion (%) of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Acceleration 0–15 This parameter adjusts the time over
which the Delay Time will change from
the current setting to a newly specified
setting. The rate of change for the Delay
Time directly affects the rate of pitch
change.
HF Damp 200–8000 Hz,
BYPASS
Adjust the frequency above which
sound fed back to the effect will be cut.
If you do not want to cut the high
frequencies of the feedback, set this
parameter to BYPASS.
Pan L64–0–63R Adjust the stereo location of the delay
sound. L64 is far left, 0 is center, and 63R
is far right.
Low Gain -15– +15 dB Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
Parameter Value Description
High Gain -15– +15 dB Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the delay sound. With
a setting of D100:0W only the direct
sound will be output, and with a setting
of D0:100W only the delay sound will be
output.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control Balance, Coarse A, Coarse B
Parameter Value Description
Mode 1, 2, 3, 4, 5 Higher settings of this parameter will
result in slower response, but steadier
pitch.
Coarse A -24– +12
semitone
Adjust the pitch of Pitch Shift A in
semitone steps (-2–+1 octaves).
Coarse B -24– +12
semitone
Adjust the pitch of Pitch Shift B in
semitone steps (-2–+1 octaves).
Fine A -100– +100
cent
Make fine adjustments to the pitch of
Pitch Shift A in 2-cent steps (-100–+100
cents).
One cent is 1/100th of a semitone.
Fine B -100– +100
cent
Make fine adjustments to the pitch of
Pitch Shift B in 2-cent steps (-100–+100
cents).
One cent is 1/100th of a semitone.
Pre Delay A 0.0–500.0 ms Adjust the time delay from when the
direct sound begins until the Pitch Shift
A sound is heard.
Pre Delay B 0.0–500.0 ms Adjust the time delay from when the
direct sound begins until the Pitch Shift
A sound is heard.
Pan A L64–0–63R Adjust the stereo location of the Pitch
Shift A sound. L64 is far left, 0 is center,
and 63R is far right.
Pan B L64–0–63R Adjust the stereo location of the Pitch
Shift B sound. L64 is far left, 0 is center,
and 63R is far right.
Level Bal A100:0B–
A0:100B
Adjust the volume balance between the
Pitch Shift A and Pitch Shift B sounds.
When set to A100:0B, only the sound of
Pitch Shift A is output; when set to
A0:100B, only the sound of Pitch Shift B
is output.
Balance D100:0W–
D0:100W
Adjust the volume balance between the
direct sound and the pitch shift sound.
With a setting of D100:0W only the
direct sound will be output, and with a
setting of D0:100W only the pitch shift
sound will be output.
Level 0–127 Adjust the output level.
Parameter Value Description
RD-700SX_e.book 139 ページ ２００６年３月２３日 木曜日 午後２時５２分