Filter
Top Products
133
Effect/Parameter List
Settings when using a pedal wah with a pedal connected to
FC1
• MFX Control: Manual
• Control Type: PEDAL
• EDIT/ 2. Control/ FC1: MFX Control
84: VR PHASER
This phaser is a descendant of the Roland VR Series effects. This
creates a swirling effect by adding sounds that are out of phase with
the original sound.
85: ORGAN MULTI
This is an effect combining the VK series internal effect with an organ
effect with the same features.
It comprises vibrato/chorus, overdrive, and rotary effects.
86: *STEREO EQ (STEREO EQUALIZER)
This is a four-band stereo equalizer (low, mid x 2, high).
Rate ( )
note (*1) Wah effect rate (note)
When Control Type is set to “TOUCH,”
this adjusts the sensitivity to the volume
used in changing the tone.
Depth 0–127 Depth of the wah effect's sweep
Phase 0–180 deg Ratio of the wah effect sound in the left
and right sides when the spread is not
distributed evenly
Low Gain -15–+15 dB Boost or cut in the low end
High Gain -15–+15 dB Boost or cut in the high end
Level 0–127 Output volume
Assignable Parameters
MFX Control Rate, Resonance, Depth
Parameter Value Description
Rate Mode Hz, Note When this is set to “note,” the effect is
synchronized with the tempo.
Rate (Hz) 0.05–10.00
Hz
Phaser Frequency (Hz)
Rate ( )
note (*1) Phaser Frequency (note)
Depth 0–127 Depth
Resonance 0–127 Feedback Level
Step Sw OFF, ON Setting this to ON creates a step phaser.
Step Rate Mode Hz, Note When this is set to “note,” the effect is
synchronized with the tempo.
StepRate(Hz) 0.10–20.00
Hz
Rate of stepped changes in phaser effect
(Hz)
Step Rate
()
note (*1) Rate of stepped changes in phaser effect
(note)
Low Gain -15–+15 dB Boost or cut in the low end
High Gain -15–+15 dB Boost or cut in the high end
Level 0–127 Output volume
Assignable Parameters
MFX Control Rotary Speed, OD Drive
Parameter Value Description
Vib/Cho
Switch
OFF, ON Switches the vibrato and chorus effects
Parameter Value Description
Vib/Cho Type V-1, V-2, V-3,
C-1, C-2, C-3
Vibrato and chorus effect types
V-1, V-2, V-3:
Adds a wavering
(vibrato) that is created by changes in
the pitch.
The effect deepens as the value is
increased
C-1, C-2, C-3:
Adds a fullness and
breadth (chorus) to the sound.
The effect deepens as the value is
increased.
Vib/Cho
Vintage
’50, ’60, ’70 This reproduces the subtle differences
in the vibrato and chorus effects in
organs built in different years.
Vib/Cho Level 0–127 Vibrato/chorus effect volume
OD Switch OFF, ON Switches the overdrive effect
OD Drive 0–127 Amount of distortion
OD Level 0–127 Overdrive effect volume
Rotary Switch OFF, ON Switches the rotary effect
Rotary Speed SLOW, FAST Low– and high-frequency rotation
speeds (Rate)
SLOW
: (Slow Rate)
FAST
: (Fast Rate)
R-Wf Slow Sp 0.05–10.00
Hz
Rate with low-frequency rotor set to
SLOW rate
R-Wf Fast Sp 0.05–10.00
Hz
Rate with low-frequency rotor set to
FAST rate
R-Wf Accel 0–15 Speed at which the low-frequency
rotor's rotation rate changes when the
rotation speed is switched
R-Wf Level 0–127 Low-frequency rotor volume
R-Tw Slow Sp 0.05–10.00
Hz
High-frequency rotor setting
This parameter is the same as that for
the low-frequency rotor.
R-Tw Fast Sp 0.05–10.00
Hz
R-Tw Accel 0–15
R-Tw Level 0–127
Rotary Separat 0–127 Amount of breadth in the sound
Rotary Level 0–127 Output volume
Assignable Parameters
MFX Control Level
Parameter Value Description
Low Freq 200, 400 Hz Select the frequency of the low range
(200 Hz/400 Hz).
Low Gain -15– +15 dB Adjust the gain of the low frequency.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Freq 2000, 4000,
8000 Hz
Select the frequency of the high range
(2000 Hz/4000 Hz/8000 Hz).
High Gain -15– +15 dB Adjust the gain of the high frequency.
Positive (+) settings will emphasize
(boost) the high frequency range.
P1 Freq 200–8000Hz Adjust the frequency of Middle 1 (mid
range).
P1 Q 0.5, 1.0, 2.0,
4.0, 8.0
This parameter adjusts the width of the
area around the Middle 1 Frequency
that will be affected by the Gain setting.
Higher values of Middle 1 Q will result
in a narrower area being affected.
P1 Gain -15– +15 dB Adjust the gain for the area specified by
the Middle 1 Frequency and Q settings.
Positive (+) settings will emphasize
(boost) the Middle 1 range.
P2 Freq 200–8000 Hz Adjust the frequency of Middle 2 (mid
range).
Parameter Value Description
RD-700SX_e.book 133 ページ ２００６年３月２３日 木曜日 午後２時５２分