Filter
Top Products
73
Chapter 3 Selecting Output Jacks
Chapter 3
* You can specify the level for each Tone using the Tone Level
parameter (TVA p. 95).
Pan (Patch pan)L64–0–63R
This determines the stereo positioning of the Patch. A setting
of L64 places the Patch at the far left, 0 in the center, and 63R
at the far right.
* You can set each Tone’s pan position using the Tone Pan
parameter (TVA p. 95).
* While each Tone in a Patch has its own Pan position, the
Patch pan setting shifts the entire Patch – including all of its
Tones – leftward or rightward.
PATCH COMMON ([PATCH]-
[COMMON])
Output Assign
This specifies the output destination for the Patch.
MFX: The Patch is sent into the Multi-Effects. Its final output
destination is determined by the Multi-Effects output
settings.
OUTPUT A–C: The Patch is sent to the selected pair of
OUTPUT A–C jacks.
INDIV 1–6: The Patch is sent to the selected INDIVIDUAL 1–
6 jack.
TONE: Each Tone in the Patch is sent to its programmed
output destination.
PATCH MFX OUT (Patch MFX Output)
([PATCH]-[EFFECTS])
Output (Output Assign) A/B/C
This specifies the pair of OUTPUT jacks to which the stereo
Multi-Effects output is routed.
Dry (Dry Output Level) 0–127
This sets the Multi-Effects output level to the selected
OUTPUT jacks.
Chorus (Chorus Send Level) 0–127
This sets the amount of the Multi-Effects output to be sent to
the Chorus.
The final output-jack destination is determined by the
Chorus output settings.
Reverb (Reverb Send Level) 0–127
This sets the amount of the Multi-Effects output to be sent to
the Reverb.
The final output-jack destination is determined by the Reverb
output settings.
PATCH CHO OUT (Patch Chorus
Output) ([PATCH]-[EFFECTS])
Output Assign (Chorus Output Assign) A/B/C
This setting selects the pair of OUTPUT jacks to which the
Chorus unit’s stereo output is routed when Chorus Output
Select is set to “MAIN” or “MAIN+R.”
Level (Chorus Level) 0–127
This setting determines the Chorus output level.
Select (Chorus Output Select)
This parameter allows you to send the Chorus output
directly to the currently selected OUTPUT jacks, to the
Reverb, or to both.
MAIN: The Chorus output is sent only to the OUTPUT jacks.
REV: The Chorus output is sent only to the Reverb.
MAIN+R: The Chorus output is sent to the OUTPUT jacks
and to the Reverb.
PATCH REV OUT (Patch Reverb Output)
([PATCH]-[EFFECTS])
Output Assign (Reverb Output Assign) A/B/C
This setting selects the OUTPUT jacks to which the Reverb
unit’s stereo output is routed.
Level (Reverb Level) 0–127
This setting determines the Reverb output level.
SYSTEM SETUP ([SYSTEM]-[COMMON])
Master Level 0–127
This adjusts the volume of the entire XV-3080.
Mix/Parallel
MIX: All sounds – including those routed to OUTPUTs B/C
or INDIVIDUAL 3–6 – are mixed together and routed to the
A(MIX) OUTPUT jacks.
This setting allows you to quickly route everything through
headphones when you are creating sounds, or to combine all
of your sounds into two outputs when sending the XV-3080’s
signal to a mixer that has only two channels.
* When MIX is selected, sounds routed to the INDIVIDUAL 3/
5 jacks are sent to the left A(MIX) OUTPUT jack, and sounds
routed to the INDIVIDUAL 4/6 jacks are sent to the right
A(MIX) OUTPUT jack.