Filter
Top Products
Basic Structure
Internal Structure (System Overview)
123
Owner’s Manual
● In the Multi mode
The Effect parameters in the Multi mode are set for each Multi.
n The Insertion effect, Plug-in Insertion effect, and the System effect cannot be applied to Parts 17-32 (using the Multi-part Plug-in board PLG100-XG).
n The Part EQ cannot be applied to Parts of the Plug-in Board.
n The System effects (Reverb, Chorus), the Master EQ, and the Master effect are not applied to the sound output through the ASSIGNABLE OUTPUT
jacks or the mLAN connector of the mLAN16E board. (Only the Part EQ and the Insertion effect are applied.)
A
B
[MULTI/SEQ PLAY] (select Multi mode) → Multi
selection → [EDIT] → [COMMON] → [F6] EFFECT →
[SF1] CONNECT
Tone Generator block
Part 1-16
Part 1 Insertion
Effect
(VCE INS)
Plug-in Insertion Effect
(PLG-EF)
System effects (Reverb effect and Chorus effect)
Chorus Ctg, Chorus Typ (Chorus Effect Category, Chorus Effect Type)
Reverb Typ (Reverv Effect Type)
Determines the effect type for Chorus.
Chorus Send, Reverb Send
Determines the level of the sound (from Insertion A or B, or the bypassed signal) that is
sent to Chorus/Reverb effect. These Parameters can be set in the Multi Play mode (*4)
Settings: Settings: 0 - 127
Chorus Return, Reverb Return
Chorus Pan, Reverb Pan
Determines the Return level and pan position setting for the Chorus/Reverb effect.
Settings: 0 - 127, L63 (far left) - C(center) - R63 (far right)
Chorus to Reverb
Determines the Send level of the signal sent from the Chorus Effect to the Reverb
Effect.
[MULTI/SEQ PLAY] (select Multi
mode) → Multi selection →
[EDIT] → [COMMON] → [F2]
MEQ/MEF → [SF2] MEF
Plug-in Part 1-3
(When the Single part
Plug-in board has
been installed)
When the PLG100-VH
has been installed
Audio Input part
Tone Generator block
Part 17-32
(When the Multi-part Plug-in Board
PLG100-XG has been installed)
Part 1
Part EQ *3
*4
Reverb Send
Chorus Send
Reverb Return
Chorus Return
Master effect
5*
Master EQ
Output
*2
*2
*2
*1
*1
*1 Select the part to which the Insertion effect is applied from Parts 1-16,
Plug-in Parts 1-3, and the audio input Part. The Insertion effect
depends on the setting of the Voice assigned to the selected part.
nAmong all of the audio input Parts, the Insertion effect can be
applied only to the A/D Input Part.
*2 Select the part to which the Plug-in Insertion effect is applied from
Parts 1-16, Plug-in Parts 1-3, and the audio input Part (Plug EF Part
parameter).
Settings: Part 01 - Part 16, Part AD, Part P2 - Part P3, off
[MULTI/SEQ PLAY] (select Multi mode) → Multi selection → [EDIT]
→ [COMMON] → [F6] EFFECT → [SF2] INS SW
[MULTI/SEQ PLAY] (select Multi mode) → Multi selection →
[EDIT] → Part selection → [F3] EQ
[MULTI/SEQ PLAY] (select Multi mode) → Multi selection →
[F4] EF SEND
[MULTI/SEQ PLAY] (select Multi mode) → Multi selection →
[EDIT] → [COMMON] → [F1] GENERAL → [SF3] MEQ OFS
[MULTI/SEQ PLAY] (select Multi mode) → Multi selection →
[EDIT] → [COMMON] → [F2] MEQ/MEF → [SF2] MEQ
*3
*4
*5