Filter
Top Products
Using the S90 ES with computer software
87
Owner’s Manual
Quick GuideConnecting the Computer and Midi devices
When controlling Digital Performer 4.52:
Functions of Mackie Control assigned to [F1] - [F6] and [SF1] -
[SF5] buttons
When turning the [VOLUME] button off, the Control sliders on the S90 ES are assigned to perform
the same functions as the Knobs on the DAW controller.
Some edited values are not shown on the S90 ES display.
Press the [DRUM KIT] button to indicate the Send/Effect number in the brackets [ ] at the top of
the LCD.
Some parameters may not be available depending on the Effect Type.
The [OPTION], [CONTROL], and [COMMAND] buttons on the Mackie Control correspond
respectively to the [EDIT], [JOB], and [STORE] buttons at left below the LCD.
Additional operations other than those listed above are available. For details, refer to the relevant
documentation of Mackie Control.
Please keep in mind that some functions may not be available.
Button/Controller names on
Mackie Control
Functions
In all modes:
[I/O] Calls up the Mode list display.
[LEVEL METERS] Turns the Meter indication on or off.
[SEL] Selects a channel.
[SHIFT] + [SEL] Selects multiple channels.
[MUTE] Mutes or unmutes each channel.
[SOLO] Sets Solo for each channel to on or off.
[REC RDY] Sets the REC RDY of each channel to on or off.
[BANK </>] Scrolls through the track indication every eight channels.
[CHANNEL </>] Scrolls through the track indication channel-by-channel.
[CONTROL]+[CYCLE] Turns Loop on or off.
[TR OVERVIEW] Moves the Track Overview to front.
[MIXING BOARD] Opens the Mixer window.
[SEQ EDITOR] Starts the Sequencer Editor window.
[SHIFT]+[SEQ EDITOR] Starts the Soundbites window.
[UNDO] Executes the Undo operation.
[REDO] Executes the Redo operation.
[SAVE] When the lamp lights, press this so that the lamp flashes.
Press this again to execute the Save operation (lamp turns
off).
[MARKER] Turns the Marker on or off.
[SHIFT]+[MARKER] Opens the Marker Option window.
[RWD] Press to continuously rewind. Press again to rewind more
quickly. When the Marker is turned on, this operation moves
the song position to the previous Marker.
[FF] Press to continuously fast-forward. Press again to fast-forward
more quickly. When the Marker is turned on, this operation
moves the song position to the next Marker.
[STOP] Stops recording or playback.
[PLAY] Press to start playback from the current point.
[REC] Press this to start song recording. The [F] (Play) and [I]
(Rec) lamp are turned on during recording.
[ZOOM] Switches between Scroll (lamp lights), Zoom (lamp is off), and
Nudge (lamp flashes).
[SCRUB] Turns Scrub on and off. When turned on, you can use the dial
to move the song position. (A malfunction may occur.)
PAN mode [PAN] (or [I/O] → knob)
Knobs 1 - 8 (turning) For editing parameters.
[DYN] + Knobs 1 - 8
(pressing)
Resets the edited parameter to the default value (center).
[FLIP] Switches the functions of the Channel Knobs and the Faders.
[PAN] in the PAN mode Turns the Meter on or off.
ASSIGNMENT
FADER BANKS
Track Groups/Windows
PAN/SEND
PAN/SEND
TONE
ARP FX
Dialog/Record
Transport/Project
EQ
TONE
TONE
ARP FX
ARP FX
EQ
SENDS
I/O PAN EQ BANK-L BANK-R SHIFT
PLUG-INS DYN DIAL RESET KN1-4/5-8
FLIP
CHANNEL-L CHANNEL-R BANK-L BANK-R SHIFT
EDIT
LEVEL METERS
DIAL RESET KN1-4/5-8
SEQ EDITOR
GROUOP UNGROUP SUSPEND BANK-L BANK-R SHIFT
TR OVERVIEW
MIXING BOARD
DIAL RESET KN1-4/5-8
OVERDUB
ENTER ESCAPE CLICK COUNTOFF SHIFT
PATCH THRU CLEAR CLIP DIAL RESET KN1-4/5-8
UNDO
SLAVE EXT SYNC
MEMORY LINK
PRE/POST ROLL
BANK-L BANK-R SHIFT
REDO SAVE
AUDIBLE MODE
KN1-4/5-8
PUNCH
MARKER EDIT GRID CYCLE BANK-L BANK-R SHIFT
SELECT SOLO DIAL RESET KN1-4/5-8
CURSOR-L
CURSOR-DWN
CURSOR-UP ZOOM BANK-L BANK-R SHIFT
CURSOR-R SCRUB DIAL RESET KN1-4/5-8
SndVal mode [SEND] (or [I/O] → knob)
Knobs 1 - 8 (turning) For editing parameters.
Cursor [UP] [DOWN] Changes the Send number.
Knobs 1 - 8 (pressing) Sets Mute to on or off.
[DYN] + Knobs 1 - 8
(pressing)
Resets the parameter value to the default (0 dB).
[FLIP] Switches the functions of the Channel Knob and the Faders.
[SEND] in the SndVal mode Turns the Meter on or off.
SndOut mode [I/O] → Knob
Cursor [UP] [DOWN] Changes the Send number.
Knobs 1 - 8 (turning) Selects the bus for each Send of the track.
Knobs 1 - 8 (turning)
(except when selecting a
bus)
Switches between Send PRE and POST.
Input mode [I/O] → Knob
Knobs 1 - 8 (turning) Selects an input bus for a track.
Output mode [I/O] → Knob
Knobs 1 - 8 (turning) Selects an output bus for a track.
Effect mode [PLUG-IN] (or [I/O] → Knob)
Knobs 1 - 8 (turning) Selects a Plug-in Effect for each track.
Cursor [UP] [DOWN] Changes the Effect Number.
Knobs 1 - 8 (pressing) Turns the Effect Bypass on or off. When the bus is turned on,
X is indicated above the Effect name.
[EQ] + Knobs 1 - 8 (pressing) Assigns the Parametric EQ to the corresponding track.
[EDIT] + Knobs 1 - 8
(pressing)
(when any track is selected)
Enters the Plug-in Effect Edit mode. (Available only when the
Plug-in Effect is selected.) Please keep in mind that some
parameters may not be available depending on the selected
Effect Type. Press the [EDIT] button again to exit from the Edit
mode.
Edit mode
Knobs 1 - 8 (turning) For editing parameters.
Cursor [UP] [DOWN] Changes an Effect Number.
[LEFT]/[RIGHT] Calls up the Effect of a different track.
[CHANNEL </>] Changes the parameters to be edited with the Knobs in order
one by one.
[BANK </>] Changes the parameters to be edited with the Knobs in
groups of eight.
[FLIP] Switches the functions of the Channel Knobs and the Faders.
Button/Controller names on
Mackie Control
Functions