Filter
Top Products
Using the Mastering Tools
G-70 Music Workstation
r
105
(8) Press the [EXIT] button to return to the main page.
Using the Mastering Tools
The G-70 contains two effects processors that apply to
all sections and parts whose signals are transmitted to
the OUTPUT MAIN sockets.
These processors are collectively called the “Mastering
Tools”, because they allow you to perfect the signal mix
output by the G-70 so as to adapt it to the sound sys-
tem you are using. Though they are not meant to be
changed for every song you intend to play, switching
settings is relatively easy and could therefore be used to
great effect.
Note: The settings of the MASTERING TOOLS effects are global
parameters that are not saved to individual User Programs. You
can, however, archive them by saving the current User Program
Set to the internal memory or a memory card.
Press the [EFFECTS] button.
On this page, you can switch the MASTERING TOOLS
processors on and off by pressing the [OFF/ON] but-
ton icons to the right of the EQUALIZER and COM-
PRESSOR “displays”.
If you only want to select another effect type, press
the EQUALIZER or COMPRESSOR display and use the
[DATA÷ENTRY] dial or the [DEC]/[INC] buttons to select
it. If you also need to change certain aspects of that
effect…
Equalizer
(1) Press the EQUALIZER [EDIT] field to access the
parameters of the same name.
The display changes to:
An equalizer has the same function as the BASS, MID
and TREBLE buttons on an amplifier: it allows you to
color the sound or to apply tonal corrections that
help you avoid saturating the speakers.
(2) Press the [ON] (or [OFF]) field to switch the equal-
izer on (icon lights) or off (icon goes dark).
You can also do so on the EFFECTS page (see above).
(3) Press the field below “EQUALIZER” that displays the
name of the currently selected preset.
(4) Select the desired equalizer preset with the
[DATA÷ENTRY] dial or the [DEC]/[INC] buttons.
The available presets are:
The settings you make on this page can be saved to a
User memory and recalled as and when necessary.
Here’s how to edit the parameters:
(5) Press the field of the parameter you wish to
change.
(6) Set the desired value with the [DATA÷ENTRY] dial or
the [DEC]/[INC] buttons.
● EQ LEVEL (0~127)—Use this parameter to set the equal-
izer’s input level. This may be necessary when the level of
the signals sent to this processor is so high that the
sound distorts.
Note: Do not set this parameter to “0” if the equalizer is
switched on, because doing so means that the OUTPUT
MAIN sockets transmit no signal whatsoever.
● EQ GAIN (–15~0~15dB)—Use this parameter to correct
the level at equalizer’s outputs. If the settings of the
remaining parameters lead to a significantly lower level
(which can be checked by switching the Equalizer on and
off for A/B comparisons), select a positive value. If your
settings lead to a significantly higher level, select a neg-
ative value. “0” means that the level is neither boosted
nor attenuated.
● HI FREQ HZ (2000, 4000, 8000)—This parameter allows
you to set the cutoff frequency of the high band (this is
a shelving filter).
● HI GAIN DB (–15~15dB)—Use this parameter to set the
level of the selected HI frequency. Positive values boost
(increase the volume of) that frequency. Negative values
cut (attenuate) it.
● MID FREQ HZ (200~8000Hz)—This parameter allows
you to set the cutoff frequency of the middle band (this
is a peaking filter).
● MID Q (0.5, 1, 2, 4, 8)—Use this parameter to specify
the width of the MID FREQ band that you want to boost
or cut. Smaller values mean that neighboring frequen-
cies above/below that value are also affected.
● MID GAIN DB (–15~15dB)—Use this parameter to set
the level of the selected MID frequency. Positive values
boost (increase the volume of) that frequency. Negative
values cut (attenuate) it.
● LO FREQ HZ (200, 400)—This parameter allows you to
set the cutoff frequency of the low band (this is a shelv-
ing filter).
● LO GAIN DB (–15~15dB)—Use this parameter to set the
level of the selected LO frequency. Positive values boost
(increase the volume of) that frequency. Negative values
cut (attenuate) it.
(7) To save the settings you have just made (in order
to use them again at a later stage), press the
[WRITE¥USER] field.
1. Flat
2. Rock
3. Pop
4. Jazz
5. Classic
6. Standard
7. User