Filter
Top Products
M7CL Owner’s Manual
Sending the signal from an input channel to the STEREO/MONO buses
64
1 Channel select button
This shows the icon, channel number, and channel
name for the channel. When you press this button, that
channel will be selected for operations, and the corre-
sponding [SEL] key will light.
B MODE button
This button selects either ST/MONO mode or LCR
mode as the way in which the signal will be sent to the
STEREO bus or MONO bus. This mode can be speci-
fied individually for each channel.
The two modes will alternate each time you press the
button. An indicator (ST/MONO or LCR) immediately
above the button will light to indicate the currently
selected mode.
C STEREO/MONO buttons
These buttons are individual on/off switches for the
signal that is sent from each channel to the STEREO
bus / MONO bus when the MONO button is set to ST/
MONO mode.
D TO ST PAN/TO ST BALANCE knob
For INPUT channels, this acts as the PAN knob that
adjusts the left/right panning of the signal sent to the
STEREO bus.
For ST IN channels, this acts as the BALANCE knob
that adjusts the volume of the left and right signals
sent to the STEREO bus. To adjust the value, press the
knob to select it, and operate the corresponding multi-
function encoder.
If the MODE button is set to LCR mode, the following
button and knob are displayed instead of the STEREO/
MONO button (
3).
E LCR button
This button is an overall on/off switch for the signals
sent from the channel to the STEREO bus and MONO
bus. If this button is off, no signals will be sent from
the corresponding input channel to the STEREO bus
or MONO bus.
F CSR knob
This knob adjusts the relative level of the signals sent
from the channel to the STEREO (L/R) bus and to the
MONO (C) bus, in a range of 0–100%. To adjust the
value, press the knob to select it, and operate the corre-
sponding multifunction encoder.
[TO STEREO/MONO popup window (ALL)]
The screen shows the status of the signals sent from all
input channels to the STEREO bus / MIX bus. Here
you can also adjust the pan or balance in groups of the
selected eight channels.
1 Channel select button
This indicates the channel number, the icon selected
for that channel, and the channel name. When you
press this button, that channel will be selected for
operations, and the corresponding [SEL] key will
light.
B TO ST PAN/TO ST BALANCE knob
For INPUT channels, this acts as the PAN knob that
adjusts the left/right panning of the signal sent to the
STEREO bus. For ST IN channels, this acts as the
BALANCE knob that adjusts the volume of the left
and right signals sent to the STEREO bus.
To adjust the value, press the knob to select it, and
operate the corresponding multifunction encoder.
If the signal reaches the overload point at any meter
detection point in that channel, the indicator at the
right of the knob will light.
C ST/MONO indicator
If a channel is set to ST/MONO mode, this individu-
ally indicates the on/off status of the signal sent from
the channel to the STEREO bus / MONO bus.
If a channel is set to LCR mode, the LCR indicator is
displayed in this location. The LCR indicator indicates
the on/off status of all signals sent from that channel to
the STEREO bus and MONO bus.
4
Access the eight-channel TO STEREO/
MONO popup window.
5
Use the MODE button to select either ST/
MONO mode or LCR mode for each chan-
nel.
6
In the STEREO / MONO MASTER section of
the top panel, make sure that the [ON] key
of the STEREO channel / MONO channel is
turned on, and raise the fader to an appro-
priate position.
5
6
3
3
1
2