Filter
Top Products
M7CL Owner’s Manual
Signal flow for output channels
80
These channels process the signals sent from MIX channels and STEREO/MONO channels to MATRIX buses, and send
them to the corresponding output ports. When the M7CL is in the default state, the following output ports are assigned.
●
ATT (Attenuator)
Attenuates/boosts the level of the signal.
●
4 BAND EQ (4 band equalizer)
A parametric EQ with four bands; HIGH, HIGH MID,
LOW MID, and LOW.
●
DYNAMICS 1
This is a dynamics processor that can be used as a com-
pressor, compander, or expander.
●
LEVEL
This adjusts the output level of the channel.
●
BALANCE (STEREO channel only)
Adjusts the left/right volume balance of the STEREO (L/
R) channel.
●
ON (On/off)
Turns the output channel on/off. If off, that channel is
muted.
●
MATRIX ON/OFF (MATRIX send on/off)
This is an on/off switch for the signal sent from the MIX
channels, STEREO (L/R) channel, or MONO (C) channel
to each MATRIX bus.
●
MATRIX (MATRIX send levels)
This adjusts the send level of the signal sent from the MIX
channels, STEREO (L/R) channel, or MONO (C) channel
to each MATRIX bus. As the position from which the sig-
nal is sent to the MATRIX bus, you can choose either,
immediately before the fader, or immediately after the
[ON] key.
If the send-destination MATRIX bus is set to stereo, you
can use the PAN knob to adjust the panning between the
two MATRIX buses. If the send-source is a stereo MIX
channel or the STEREO channel, use the BALANCE
knob to adjust the volume balance of the left and right
channels sent to the two MATRIX buses.
●
INSERT
You can patch the desired output/input ports to insert an
external device such as an effect processor. You can switch
the insert-out and insert-in locations.
●
METER
This meters the level of the output channel. You can
switch the position at which the level is detected.
●
KEY IN (MIX channels 13–16 only)
You can send the output signals of MIX channels 13–16 to
dynamics processors and use them as key-in signals to
control the dynamics.
●
RACK IN PATCH
This patches the output signal of the output channel to an
input of the rack.
●
OUTPUT PATCH
This assigns an output port to an output channel.
●
MONITOR SELECT
This selects the output signal of an output channel as a
monitor source.
MATRIX CUE
MIX
ST
L R (C) L R
1 2
1516
1 2 7 8
M
O
N
O
···
···
To RACKIN PATCH
To OUTPUT PACH
INSERT POIN
GR METER
COMP
COMPAND
EXPAND
DYNA OUT
EQ OUT
LEVEL
BAL
ON
POST ON
POST
ON
4BAND
EQ
PRE EQ
AT T
INSERT
PRE FADER
PRE FADER
PRE FADER
INSERT OUT
METER
INSERT
LEVEL
ON
ON
ON
LEVEL
LEVEL
PA N
CUE ON
MATRIX2,4...8
MATRIX1,3...7
PRE EQ POST EQ
METER METER METER
METER
STEREO
INSERT OUT L,R,MONO (C)
STEREO
INSERT IN L,R,MONO (C)
STEREO OUT
L,R,MONO (C)
To OUTPUT PATCH
To MONITOR SELECT
STEREO L,R,MONO(C)
POST ON INSERT OUT
PRE FADER INSERT OUT
PRE EQ INSERT OUT
PRE EQ
INSERT OUT
Keyin
Self PRE EQ / Self POST EQ / MIX13-16 OUT /
ST (L,R,MONO (C)) POST EQ
(PRE FADER) PFL / (POST ON) AFL
PRE FADER / POST ON
PRE FADER / POST ON
To MATRIX
To MATRIX
VARI
STEREO
VARI
INSERT
POST ON
INSERT OUT
■ MATRIX channels
MATRIX CUE
MIX
ST
L R (C) L R
1 2
1516
1 2 7 8
M
O
N
O
···
···
To RACKIN PATCH
To OUTPUT PATCH
PRE EQ
PRE EQ
POST EQ
INSERT
Keyin
PRE FADER
MATRIX1-8 POST EQ
(PRE FADER) PFL / (POST ON) AFL
PRE FADER
INSERT OUT
LEVEL
INSERT
POST
ON
POST ON
ON
PRE EQ
INSERT OUT
CUE ON
AT T
4BAND
EQ
EQ OUT DYNA OUT
GR METER
PRE FADER
METER METER METER METER
METER
MATRIX OUT 1-8
MATRIX
INSERT OUT 1-8
MATRIX
INSERT IN 1-8
To OUTPUT PATCH
To MONITOR SELECT
MATRIX 1-8
INSERT POINT
PRE FADER INSERT OUT
POST ON INSERT OUT
PRE EQ INSERT OUT
COMP
COMPAND
EXPAND
Self PRE EQ / Self POST EQ / MIX13-16 OUT/
INSERT
POST ON
INSERT OUT
• M7CL-32/48
MATRIX channels 1–8
Slot 3 output channels 1–8, 9–16
MATRIX channels 1/2
OMNI OUT jacks 13/14
• M7CL-48ES (Daisy Chain)
MATRIX channels 1–6 EtherSound output channels 17–22
MATRIX channels 1–4 OMNI OUT jacks 1–4
MATRIX channels 1–8 Slot 3 output channels 1–8, 9–16