Filter
Top Products
102
These algorithms can be selected as an insert effect if
“1in1outx8” is selected for “SelectEffType.”
Different insert effects can be used on each of eight channels/
tracks.
Effects MN1–MN11 are monaural type effects.
“1in1outx8” effects cannot be controlled by an expression
pedal etc.
88: MN1: OverDrive/HighGain
The parameters are the same as for ODHIG.
89: MN2: Compressor2
The parameters are the same as for Comp2.
90: MN3: Limiter
The parameters are the same as for Comp2.
91: MN4: Gate
92: MN5: Exciter2
The parameters are the same as for Excit2.
93: MN6: Parametric 4band EQ
94: MN7: Amp Simulator
95: MN8: Multitap Delay
The parameters are the same as for Mt.Dly.
96: MN9: Chorus/Flanger2
The parameters are the same as for ChFl2.
97: MN10: Phaser
The parameters are the same as for Phaser.
98: MN11: Expander
This effect makes the sound tighter and improves the dynamic
range and S/N ratio by compressing signals that are below a
specified level.
Cntrl (Control)
Select the parameter that will be controlled by an expression
pedal or an external MIDI controller, and specify the range of
parameter values for control.
: Param
Select the parameter to be controlled. The parameters that can
be selected will differ depending on the program.
For example, the “Cho/Fl-Depth” selection for “Param” will
control the “Depth” parameter of the Cho/Fl. When this is
“Off,” control will not occur.
: Max, : Min
Specify the upper and lower limits of the range in which the
parameter value will be controlled. By exchanging the “Max”
and “Min” values, you can (for example) reverse the effect
that occurs when a pedal is advanced and released.
The available values will depend on the effect. “Max” and
“Min” will not be displayed when “Param” is set to “Off” or
“Wah.”
Using a pedal to control wah
1 As explained in “Controlling an effect from an external
device” (→p.33), make settings for “Device” etc. and select
an effect program that provides a wah.
2 Press the “(EffectIcon)” button for “Ctrl,” and set “Param”
to “Wah.”
3 Press the “(EffectIcon)” button for “Wah,” and set “Mode”
to “Pedal.”
Insert (1in1outx8)
Thrshl (Threshold)............................0...100 Sets the level to which the Gate is
applied
Polrty ([G] Polarity) ................................+, – Switches between non-reversed and
reversed Gate on/off
Attack ([G] Attack) ............................1...100 Sets the attack time
Relse (Release)................................1...100 Sets the release time
Trim (Trim).........................................0...100 Sets the parametric EQ input level
Fc1 (Band1 Cutoff [Hz]).............20...1.0kHz Sets the center frequency of Band 1
Q1 (Q)...........................................0.5...10.0 Sets the bandwidth of Band 1
G1 (Gain [dB]) ......................... –18...+18dB Sets the gain of Band 1
Fc2 (Band2 Cutoff [Hz]).........300...10.0kHz Sets the center frequency of Band 2
Q2 (Q)...........................................0.5...10.0 Sets the bandwidth of Band 2
G2 (Gain [dB]) ......................... –18...+18dB Sets the gain of Band 2
Fc3 (Band3 Cutoff [Hz]).........300...10.0kHz Sets the center frequency of Band 3
Q3 (Q)...........................................0.5...10.0 Sets the bandwidth of Band 3
G3 (Gain [dB]) ......................... –18...+18dB Sets the gain of Band 3
Fc4 (Band4 Cutoff [Hz]).........500...20.0kHz Sets the center frequency of Band 4
Q4 (Q)...........................................0.5...10.0 Sets the bandwidth of Band 4
G4 (Gain [dB]) ......................... –18...+18dB Sets the gain of Band 4
Type (Amplifier Type) ....................AMP1...5 Selects the type of guitar amplifier
Thrshl (Threshold) ............................0...127 Sets the level at which the effect begins
to apply
Ratio (Ratio)...............................1.0:1...inf:1 Specifies the compression ratio
Attack (Attack)...................................1...100 Specifies the length of the attack
Relse (Release)................................1...100 Specifies the length of the release
Respo (Response)............................1...100 Specifies the speed at which change
will occur in response to the input
Effect Control
Param (Parameter)..................................*** Name of parameter to be controlled
Max..........................................................*** Maximum value of parameter to be con-
trolled
Min...........................................................*** Minimum value of parameter to be con-
trolled