Korg D16 Musical Instrument User Manual


 
91
The “Attack” and “Release” parameters specify attack time and
release time of delay level control.
13: DL6: St.Auto Panning Delay
(Stereo Auto Panning Delay)
This stereo delay effect pans the delay sound left and right
using the LFO.
Modulation MO1 MO7
Category: Modulation-type effects
14: MO1: St.Chorus (Stereo Chorus)
This effect adds thickness and warmth to the sound by modu-
lating the delay time of the input signal. A two-band equalizer
can be used to adjust the tone of the effect sound. You can con-
trol the spaciousness of the sound by offsetting the phase of
the left and right LFOs from each other.
: L Pre Delay [msec], : R Pre Delay [msec]
Setting the left and right delay time individually allows you to
control the stereo image.
15: MO2: St.Flanger (Stereo Flanger)
This effect gives a significant swell and movement of pitch to
the sound. It is more effective when applied to a sound with a
lot of harmonics. This is a stereo flanger. You can add spread
to the sound by offsetting the phase of the left and right LFOs
from each other.
: LFO Shape
Changing the LFO waveform shape controls the peak sweep of
flanging effects.
: Feedback, : Wet/Dry
The peak shape of the positive and negative “Feedback” value is
different. The harmonics will be emphasized when the effect
sound is mixed with the dry sound if you set a positive value for
both “Feedback” and “Wet/Dry”, and if you set a negative value
for both “Feedback” and “Wet/Dry”.
: High Damp [%]
This parameter sets the amount of damping of the feedback in the
high range. Increasing the value will cut high-range harmonics.
16: MO3: St.Phaser (Stereo Phaser)
This effect creates a swell by shifting the phase. It is very effec-
tive on electric piano sounds. This is a stereo effect, and you
can control the spaciousness of the sound by offsetting the
phase of the left and right LFOs from each other.
: Resonance, : Wet/Dry
The peak shape of the positive and negative Feedback value is dif-
ferent. The harmonics will be emphasized when the effect sound is
mixed with the dry sound, if you set a positive value for both
“Resonance” and “Wet/Dry”, and if you set a negative value for
both “Resonance” and “Wet/Dry”.
: High Damp [%]
This parameter sets the amount of damping of the resonance in the
high range. Increasing the value will cut high-range harmonics.
17: MO4: St.Vibrato (Stereo Vibrato)
This effect causes the pitch of the input signal to shimmer. You
can use an expression pedal etc. to gradually increase or
decrease the shimmering speed.
LTime (L Delay Time [msec]).......0...680ms Sets the delay time for the left channel
LFback (L Feedback)................–100...+100 Sets the feedback amount for the left
channel
RTime (R Delay Time [msec]) .....0...680ms Sets the delay time for the right channel
RFback (R Feedback) ..............–100...+100 Sets the feedback amount for the right
channel
HiDamp (High Damp [%]).................0...100 Sets the damping amount in the high
range
LoDamp (Low Damp [%]).................0...100 Sets the damping amount in the low
range
LFO (LFO Waveform)....................TRI, SIN Selects LFO Waveform
Shape (LFO Shape).................–100...+100 Determines how much the LFO wave-
form is changed
Phase (LFO Phase [degree]) ...–180...+180 Sets the LFO phase difference between
the left and right
*Speed(Panning Frequency [Hz])..................
0.02...20.0Hz
Sets the panning speed
*Depth (Panning Depth).....................0...100 Sets the panning width
Mix (Wet/Dry)..........Dry, 1:99...99:1, Wet Sets the balance between the effect
and dry sounds
LFO (LFO Waveform)....................TRI, SIN Selects LFO Waveform
Phase (LFO Phase [degree]) ...–180...+180 Sets the LFO phase difference between
the left and right
*Speed (LFO Frequency [Hz])..0.02...20.0Hz Sets the LFO speed
LDly (L Pre Delay [msec])........0.0...50.0ms Sets the delay time for the left channel
RDly (R Pre Delay [msec]) ......0.0...50.0ms Sets the delay time for the right channel
*Depth (Depth)...................................0...100 Sets the depth of LFO modulation
EQTrim (EQ Trim).............................0...100 Sets the EQ input level
LEQG (Pre LEQ Gain [dB])....–15.0...+15.0 Sets the gain of Low EQ
HEQG (Pre HEQ Gain [dB])...–15.0...+15.0 Sets the gain of High EQ
Mix (Wet/Dry) ................. –Wet...–1:99, Dry,
1:99...Wet
Sets the balance between the effect
and dry sounds
Time (Delay Time [msec])........0.0...50.0ms Sets the delay time from the original
sound
LFO (LFO Waveform)....................TRI, SIN Selects LFO Waveform
Shape (LFO Shape).................–100...+100 Determines how much the LFO wave-
form is changed
Phase (LFO Phase [degree])....–180...+180 Sets the LFO phase difference between
the left and right
*Speed (LFO Frequency [Hz]).0.02...20.0Hz Sets the LFO speed
*Depth (Depth) ...................................0...100 Sets the depth of LFO modulation
Fdback (Feedback)...................–100...+100 Sets the feedback amount
HiDamp (High Damp [%]).................0...100 Sets the feedback damping amount in
the high range
Mix (Wet/Dry)..................–Wet...–1:99, Dry,
1:99...Wet
Sets the balance between the effect
and dry sounds
LFO (LFO Waveform) ....................TRI, SIN Selects LFO Waveform
Shape (LFO Shape) .................–100...+100 Determines how much the LFO wave-
form is changed
Phase (LFO Phase [degree])....–180...+180 Sets the LFO phase difference between
the left and right
*Speed (LFO Frequency [Hz]).0.02...20.0Hz Sets the LFO speed
Manual (Manual)...............................0...100 Sets the frequency to which the effect is
applied
*Depth (Depth) ...................................0...100 Sets the depth of LFO modulation
Reso (Resonance)....................–100...+100 Sets the resonance amount
HiDamp (High Damp [%]).................0...100 Sets the resonance damping amount in
the high range
Mix (Wet/Dry)..................–Wet...–1:99, Dry,
1:99...Wet
Sets the balance between the effect
and dry sounds
LFO (LFO Waveform) ....................TRI, SIN Selects LFO Waveform
Shape (LFO Shape) .................–100...+100 Determines how much the LFO wave-
form is changed
*Speed (LFO Frequency [Hz]).0.02...20.0Hz Sets the LFO speed
*Depth (Depth) ...................................0...100 Sets the depth of LFO modulation
Mix (Wet/Dry).............. Dry, 1:99...99:1, Wet Sets the balance between the effect
and dry sounds
EffectIns(2in2outx2)/Mst/Final