Filter
Top Products
104
Routing settings and effect set-
tings
The insert effects, master effects, and master EQ have the
same structure in all modes, but the routing settings will
determine how the oscillators of a program or the timbres
of a combination or track of a song will be sent to each
insert effect or master effect. In the pages that follow, we
will explain how you can make routing settings and effect
settings in each mode.
Effect settings for a program
Routing
1 In Program P8: Edit-Insert Effect, select the Routing
page.
2 Use “BUS Select (IFX/Indiv.Out Assign) to specify
the bus (insertion effect) to which the output of the
oscillator will be sent.
L/R: Send the output to the L/R bus. Instead, it is sent
to AUDIO OUTPUT (MAIN) L/MONO and R after the
Master EQ.
IFX1–5: The signal is sent to Insert Effects IFX 1, 2, 3, 4,
5.
1, 2, 3(Tube), 4(Tube), 1/2, 3/4(Tube): The signal is sent
to AUDIO OUTPUT (INDIVIDUAL) 1, 2, 3(Tube),
4(Tube) (☞p.109).
Off: The output will not be sent to the L/R bus, IFX1–5
buses, or 1–4(Tube) buses. Choose the Off setting if you
want to connect the oscillator output to a master effect
in series. Use “Send 1 (to MFX1)” and “Send 2 (to
MFX2)” to adjust the send level.
3 OSC MFX Send specifies the send level from each
oscillator to the master effects.
This can be set only when “BUS Select (IFX/Indiv.Out
Assign)” is either L/R or Off.
If “BUS Select (IFX/Indiv.Out Assign)” is set to IFX1–5,
the send level to the master effects is set by “Send 1”
and “Send 2” (Insert FX page) after the signal passes
through the insert effects.
Insert effects
4 Select the Insert FX page.
5 For IFX1–5, select the effect type for each insert effect.
When you press the popup button, all effects will be
displayed, organized into six categories. Use the
pages located at the left to select a category, and select
an effect from that category on the LCD screen.
You can select effects 000–089 for IFX1, 2, 3, 4, 5,
MFX1 and MFX2. You can select the double-size
effects 090–102 for IFX2, IFX3, or IFX4.
You can use the “Copy Insert Effect” page menu com-
mand to copy effect settings from another program
etc. Also, you can use “Swap Insert Effect” to
exchange (for example) IFX1 and IFX5.
6 Press the ON/OFF button to turn on the insert effect.
Each time you press the button, the insert effect will be
switched on/off. When OFF, the result will be the same
as when 000: No Effect is selected. The input sound
will be output without change.
7 Make “Chain” settings.
If the “Chain” check box is checked, the insert effect
will be connected in series. Since the output of the
oscillator is being sent to IFX1 in 1, making settings as
shown in the diagram 4 would connect all five inser-
tion effects IFX1 → IFX2 → IFX3 → IFX4 → IFX5 in
series, so that these effects would be inserted into the
output of the oscillator.
8 Make settings for “Pan (CC#8),” “BUS Sel. (BUS
Select),” “Send 1,” and “Send 2” for the sound after it
has passed through the insert effects.
If the “Chain” check box is checked, the settings that
follow the last IFX will be used.
“Pan”: Sets the pan. This is valid only when BUS Sel. is
L/R.
“BUS Sel.” (BUS Select): Specifies the output destina-
tion. Normally you will set this to L/R. If you wish to
send the sound that has passed through the insert
effects to AUDIO OUTPUT (INDIVIDUAL) 1–4, select
1–4(Tube), 1/2, or 3/4(Tube). For details on 3(Tube),
4(Tube), or 3/4(Tube), refer to p.109.
“Send 1”, “Send 2”: Sets the send levels to the master
effects. For this example, set this to 127.
9 Select the IFX1–5 pages, and set the parameters for
each of the selected effects.
For details on the parameters of each effect (☞PG
p.217–).