Filter
Top Products
121
Editing a Audio Phrase (Sample)
5.
Press [F6 (EXEC)].
A message will ask you for confirmation.
6.
To execute, press [F6 (EXEC)].
* To cancel, press [F5 (CANCEL)].
In some cases, the audio quality will be improved if you boost the
high-frequency range of an imported sample. Also, the high-
frequency range of the sample may be emphasized when you use a
sampler made by another manufacturer. In this case, you can
minimize the change in tonal character by attenuating the high-
frequency range.
* You cannot execute this with more than one sample selected.
1.
In the SAMPLE EDIT screen, press [F3 (MODIFY)] to open
the Sample Modify Menu window.
2.
Press [F1 (TRUNC&EMPHS)], and then press [F2 (EMPHS)].
fig.EMPHASIS
3.
Use the VALUE dial or [INC] [DEC] to select the emphasis
type.
PreEmphasis:
Emphasizes the high-frequency range.
DeEmphasis:
Attenuates the high-frequency range.
4.
If you want to replace the current sample with the
emphasized sample, press [F4 (OVER WRITE)] to display
the “
✔
” mark.
5.
Press [F6 (EXEC)].
A message will ask you for confirmation.
6.
To execute, press [F6 (EXEC)].
* To cancel, press [F5 (CANCEL)].
This operation raises the level of the entire sample as much as
possible without exceeding the maximum level. It is a good idea to
boost the volume by executing the Normalize operation.
* You cannot execute this with more than one sample selected.
1.
In the SAMPLE EDIT screen, press [F3 (MODIFY)] to open
the Sample Modify Menu window.
2.
Press [F2 (NORM & AMP)], and then press [F1 (NORM)].
fig.NORMALIZE
3.
If you want to replace the current sample with the
normalized sample, press [F4 (OVER WRITE)] to display the
“
✔
” mark.
4.
Press [F6 (EXEC)].
A message will ask you for confirmation.
5.
To execute, press [F6 (EXEC)].
* To cancel, press [F5 (CANCEL)].
This operation adjusts the volume of the entire sample. You can also
apply an envelope (time-variant change) to the volume of the sample.
* You cannot execute this with more than one sample selected.
1.
In the SAMPLE EDIT screen, press [F3 (MODIFY)] to open
the Sample Modify Menu window.
2.
Press [F2 (NORM & AMP)], and then press [F2 (AMP)].
fig.AMP
3.
If you want to adjust the volume of the entire sample, use the
VALUE dial or [INC] [DEC] to set the rate of volume boost.
4.
If you want to apply an envelope, specify points.
Press [F3 (POINT)] to display the “
✔
” mark. Then press [ ]
[ ] to select a parameter, and then use the VALUE dial or
[INC] [DEC] to set the value.
5.
If you want to replace the current sample with the edited
sample, press [F4 (OVER WRITE)] to display the “
✔
” mark.
6.
Press [F6 (EXEC)].
A message will ask you for confirmation.
7.
To execute, press [F6 (EXEC)].
* To cancel, press [F5 (CANCEL)].
Boosting or Limiting the High-
frequency Range of the Sample
(EMPHASIS)
Maximizing the Volume of a
Sample (NORMALIZE)
AMP
Parameter
Explanation
Rate
Rate of volume boost:
0–400%
Specifies how much boost will be applied relative to the
current volume
Parameter
Explanation
Current
Point
Currently selected point
Beginning near the start point, the points will be num-
bered 1, 2, 3, or 4.
Point 1–4 Location of the current point
Rate 1–4 Amplification ratio of the current point:
0–400%
Specifies how the volume of each point is to be boosted
relative to the current value.
JUNO-G_e.book 121 ページ ２００６年２月１３日 月曜日 午後２時４４分