Filter
Top Products
217
MIDI Implementation
2. Data Transmission
(Sound Generator Section)
■
Channel Voice Messages
●
Note off
Status
2nd byte 3rd byte
8nH kkH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 00H - 7FH (0 - 127)
vv = note off velocity: 00H - 7FH (0 - 127)
●
Note on
Status
2nd byte 3rd byte
9nH kkH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 00H - 7FH (0 - 127)
vv = note on velocity: 01H - 7FH (1 - 127)
●
Control Change
* By selecting a controller number that corresponds to the setting of parameters of
controllers (REALTIME CONTROL knob, and so on), the JUNO-G can transmit any
control change message.
❍
Bank Select (Controller number 0, 32)
Status
2nd byte 3rd byte
BnH 00H mmH
BnH 20H llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384)
* These messages are transmitted when Patch, Rhythm Set or Performance is selected. But
not transmitted when Transmit Program Change or Transmit Bank Select parameter
(SYSTEM/MIDI) is OFF.
* In Performance mode, these messages are not transmitted when External Bank Select
MSB or External PC Number parameter (PERFORMANCE/PART) is OFF.
* Although with the JUNO-G you can select the Bank Select messages to be transmitted, be
sure to refer to
Bank Select and Program Change Correspondence Chart
(p. 240) for
the Bank Select messages transmitted when the JUNO-G is select a Patch, Rhythm Set or
Performance.
* The Bank Select Numbers corresponding to SRX series should be referred to the SRX
series owner’s manual.
❍
Modulation (Controller number 1)
Status
2nd byte 3rd byte
BnH 01H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Modulation depth: 00H - 7FH (0 - 127)
❍
Breath type (Controller number 2)
Status
2nd byte 3rd byte
BnH 02H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* JUNO-G transmits this message when you operate ACTIVE EXPRESSION with the D
Beam controller.
❍
Portamento Time (Controller number 5)
Status
2nd byte 3rd byte
BnH 05H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Portamento Time: 00H - 7FH (0 - 127)
❍
Data Entry (Controller number 6, 38)
Status
2nd byte 3rd byte
BnH 06H mmH
BnH 26H llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = the value of the parameter specified by RPN/NRPN
mm = MSB, ll = LSB
❍
Volume (Controller number 7)
Status
2nd byte 3rd byte
BnH 07H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Volume: 00H - 7FH (0 - 127)
* In Performance mode, these messages are not transmitted when External Level
parameter (PERFORMANCE/PART) is OFF.
❍
Panpot (Controller number 10)
Status 2nd byte 3rd byte
BnH 0AH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Panpot: 00H - 40H - 7FH (Left - Center - Right),
* In Performance mode, these messages are not transmitted when External Pan parameter
(PERFORMANCE/PART) is OFF.
❍
Expression (Controller number 11)
Status 2nd byte 3rd byte
BnH 0BH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Expression: 00H - 7FH (0 - 127)
❍
Hold 1 (Controller number 64)
Status
2nd byte 3rd byte
BnH 40H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON
* When Continuous Hold Pedal parameter (SYSTEM/CTRL) is OFF, just only 00H (0FF)
and 7FH (0N) can be send as the control value.
❍
Portamento (Controller number 65)
Status
2nd byte 3rd byte
BnH 41H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
❍
Resonance (Controller number 71)
Status
2nd byte 3rd byte
BnH 47H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv= Resonance value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
❍
Release Time (Controller number 72)
Status
2nd byte 3rd byte
BnH 48H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Release Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
❍
Attack time (Controller number 73)
Status
2nd byte 3rd byte
BnH 49H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Attack time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
❍
Cutoff (Controller number 74)
Status
2nd byte 3rd byte
BnH 4AH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Cutoff value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
❍
General Purpose Controller 5 (Controller number 80)
Status
2nd byte 3rd byte
BnH 50H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
❍
General Purpose Controller 6 (Controller number 81)
Status
2nd byte 3rd byte
BnH 51H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
JUNO-G_e.book 217 ページ ２００６年２月１３日 月曜日 午後２時４４分