Filter
Top Products
57
Creating a Rhythm Set
For details regarding effect settings, refer to the pages shown below.
•
Making Effect Settings
(p. 125)
•
Making Multi-Effects Settings (MFX1–3)
(p. 129)
•
Making Chorus Settings
(p. 154)
•
Making Reverb Settings
(p. 155)
Output Settings (OUTPUT)
Parameter
Value Explanation
Rhythm Out Assign
MFX,
A, B, 1–
4,
TONE
Specifies for each rhythm set how the direct sound will be output.
MFX:
Output in stereo through multi-effects. You can also apply chorus or reverb to the sound that passes through multi-
effects.
A, B:
Output to the OUTPUT A (MIX) jacks or OUTPUT B jacks in stereo without passing through multi-effects.
1–4:
Output to the INDIVIDUAL 1–4 jacks in mono without passing through multi-effects.
TONE:
Outputs according to the settings for each rhythm tone.
* If you’ve made settings so that sounds are separately routed to the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, but no plug is actually
inserted in the INDIVIDUAL 2 jack, the sounds routed to INDIVIDUAL 1 and INDIVIDUAL 2 will be mixed and output from the
INDIVIDUAL 1 jack.
* If the Mix/Parallel parameter is set to “MIX,” all sounds are output from the OUTPUT A (MIX) jacks in stereo (p. 158).
Tone Out Assign
MFX,
A, B, 1–
4
Specifies how the direct sound of each rhythm tone will be output.
MFX:
Output in stereo through multi-effects. You can also apply chorus or reverb to the sound that passes through multi-
effects.
A, B:
Output to the OUTPUT A (MIX) jacks or OUTPUT B jacks in stereo without passing through multi-effects.
1–4:
Output to the INDIVIDUAL 1–4 jacks in mono without passing through multi-effects.
* If the Rhythm Out Assign is set to anything other than “TONE,” these settings will be ignored.
* If you’ve made settings so that sounds are separately routed to the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, but no plug is actually
inserted in the INDIVIDUAL 2 jack, the sounds routed to INDIVIDUAL 1 and INDIVIDUAL 2 will be mixed and output from the
INDIVIDUAL 1 jack.
* If the Mix/Parallel parameter is set to “MIX,” all sounds are output from the OUTPUT A (MIX) jacks in stereo (p. 158).
* If you’ve set Tone Out Assign to “MFX,” set the MFX Output Assign parameter (p. 127) to specify the output destination of the sound
that has passed through the multi-effects.
* Sounds are output to chorus and reverb in mono at all times.
* The output destination of the signal after passing through the chorus is set with the Chorus Output Select and Chorus Output Assign
parameters (p. 127).
* The output destination of the signal after passing through the reverb is set with the Reverb Output Assign parameter (p. 127).
Tone Out Level
0–127 Level of the signal that is sent to the output destination specified by Tone Output Assign
Send Level (Output = MFX)
Tone Chorus Send
0–127 Level of the signal sent to chorus for each rhythm tone if the tone is sent through MFX
Tone Reverb Send 0–127 Level of the signal sent to reverb for each rhythm tone if the tone is sent through MFX
Send Level (Output = non MFX)
Tone Chorus Send
0–127 Level of the signal sent to chorus for each rhythm tone if the tone is not sent through MFX
Tone Reverb Send 0–127 Level of the signal sent to reverb for each rhythm tone if the tone is not sent through MFX
Setting Effects for a Patch (Effects/MFX/MFX Control/Chorus/Reverb)
T1 T2 T3 T4
L3
L1
L2
Note off
Level
TVA Envelope
Time
Note on
JUNO-G_e.book 57 ページ ２００６年２月１３日 月曜日 午後２時４４分