Filter
Top Products
150
Adding Effects
66: OVERDRIVE
→
CHORUS
fig.MFX-66
67: OVERDRIVE
→
FLANGER
fig.MFX-67
68: OVERDRIVE
→
DELAY
fig.MFX-68
69: DISTORTION
→
CHORUS
The parameters are essentially the same as in “66: OVERDRIVE
→
CHORUS,” with the exception of the following two.
Overdrive Drive
→
Distortion Drive, Overdrive Pan
→
Distortion Pan
fig.MFX-69
70: DISTORTION
→
FLANGER
The parameters are essentially the same as in “67: OVERDRIVE
→
FLANGER,” with the exception of the following two.
Overdrive Drive
→
Distortion Drive, Overdrive Pan
→
Distortion Pan
fig.MFX-70
71: DISTORTION
→
DELAY
The parameters are essentially the same as in “68: OVERDRIVE
→
DELAY,” with the exception of the following two.
Overdrive Drive
→
Distortion Drive, Overdrive Pan
→
Distortion Pan
fig.MFX-71
Parameter
Value Explanation
Overdrive
Drive #
0–127 Degree of distortion
Also changes the volume.
Overdrive
Pan #
L64–63R Stereo location of the overdrive
sound
Chorus Pre
Delay
0.0–100.0 ms Adjusts the delay time from the
direct sound until the chorus
sound is heard.
Chorus Rate # 0.05–10.00 Hz, note Frequency of modulation
Chorus Depth 0–127 Depth of modulation
Chorus
Balance #
D100:0W–D0:100W Adjusts the volume balance be-
tween the sound that is sent
through the chorus (W) and the
sound that is not sent through
the chorus (D).
Level 0–127 Output Level
Parameter
Value Explanation
Overdrive
Drive #
0–127 Degree of distortion
Also changes the volume.
Overdrive
Pan #
L64–63R Stereo location of the overdrive
sound
Flanger Pre
Delay
0.0–100.0 ms Adjusts the delay time from
when the direct sound begins
until the flanger sound is heard.
Flanger Rate # 0.05–10.00 Hz, note Frequency of modulation
Flanger Depth 0–127 Depth of modulation
Flanger
Feedback #
-98– +98 % Adjusts the proportion of the
flanger sound that is fed back
into the effect. Negative (-) set-
tings will invert the phase.
Flanger
Balance #
D100:0W–D0:100W Adjusts the volume balance be-
tween the sound that is sent
through the flanger (W) and the
sound that is not sent through
the flanger (D).
Level 0–127 Output Level
L in
R in
Chorus
Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
L in
R in
Flanger
Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
L in
R in
Delay
Overdrive
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
Parameter
Value Explanation
Overdrive
Drive #
0–127 Degree of distortion
Also changes the volume.
Overdrive Pan # L64–63R Stereo location of the over-
drive sound
Delay Time 0–2600 ms, note Adjusts the delay time from
the direct sound until the de-
lay sound is heard.
Delay
Feedback #
-98– +98 % Adjusts the proportion of the
delay sound that is fed back
into the effect. Negative (-)
settings will invert the phase.
Delay HF Damp 200–8000 Hz,
BYPASS
Adjusts the frequency above
which sound fed back to the
effect will be cut. If you do not
want to cut the high frequen-
cies, set this parameter to BY-
PASS.
Delay Balance # D100:0W–D0:100W Adjusts the volume balance
between the sound that is sent
through the delay (W) and the
sound that is not sent through
the delay (D).
Level 0–127 Output Level
L in
R in
Chorus
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
L in
R in
Flanger
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
L in
R in
Delay
Distortion
L out
R out
Balance W
Balance W
Balance D
Balance D
Feedback
JUNO-G_e.book 150 ページ ２００６年２月１３日 月曜日 午後２時４４分