Filter
Top Products
136
Adding Effects
17: TREMOLO
Cyclically modulates the volume to add tremolo effect to the sound.
fig.MFX-17a
18: AUTO PAN
Cyclically modulates the stereo location of the sound.
fig.MFX-18a
19: STEP PAN
This uses a 16-step sequence to vary the panning of the sound.
fig.MFX-19
20: SLICER
By applying successive cuts to the sound, this effect turns a
conventional sound into a sound that appears to be played as a
backing phrase. This is especially effective when applied to sustain-
type sounds.
fig.MFX-20
Parameter
Value Explanation
Mod Wave TRI, SQR, SIN,
SAW1, SAW2
Modulation Wave
TRI:
triangle wave
SQR:
square wave
SIN:
sine wave
SAW1/2:
sawtooth wave
Rate # 0.05–10.00 Hz, note Frequency of the change
Depth # 0–127 Depth to which the effect is applied
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Level 0–127 Output Level
Parameter Value Explanation
Mod Wave
TRI, SQR, SIN,
SAW1, SAW2
Modulation Wave
TRI:
triangle wave
SQR:
square wave
SIN:
sine wave
SAW1/2:
sawtooth wave
Rate # 0.05–10.00 Hz, note Frequency of the change
Depth # 0–127 Depth to which the effect is applied
Low Gain -15– +15 dB Gain of the low range
High Gain -15– +15 dB Gain of the high range
Level 0–127 Output Level
L in
R in
L out
R out
Tremolo
2-Band EQ
2-Band EQ
Tremolo
SAW1 SAW2
L in
R in
L out
R out
Auto Pan
2-Band EQ
2-Band EQ
Auto Pan
SAW1 SAW2
L
R
L
R
Parameter Value Explanation
Step 01–16
L64–63R Pan at each step
Rate # 0.05–10.00 Hz, note Rate at which the 16-step se-
quence will cycle
Attack # 0–127 Speed at which the pan changes
between steps
Input Sync
Sw
OFF, ON Specifies whether an input note
will cause the sequence to re-
sume from the first step of the se-
quence (ON) or not (OFF)
Input Sync
Threshold
0–127 Volume at which an input note
will be detected
Level 0–127 Output volume
Parameter
Value Explanation
Step 01–16
0–127 Level at each step
Rate # 0.05–10.00
Hz, note
Rate at which the 16-step sequence will
cycle
Attack # 0–127 Speed at which the level changes be-
tween steps
Input Sync
Sw
OFF, ON Specifies whether an input note will
cause the sequence to resume from the
first step of the sequence (ON) or not
(OFF)
Input Sync
Threshold
0–127 Volume at which an input note will be
detected
Mode LEGATO,
SLASH
Sets the manner in which the volume
changes as one step progresses to the
next.
LEGATO:
The change in volume from
one step’s level to the next remains
unaltered. If the level of a following
step is the same as the one preceding
it, there is no change in volume.
SLASH:
The level is momentarily set
to 0 before progressing to the level of
the next step. This change in volume
occurs even if the level of the follow-
ing step is the same as the preceding
step.
Shuffle # 0–127 Timing of volume changes in levels for
even-numbered steps (step 2, step 4, step
6...).
The higher the value, the later the beat
progresses.
Level 0–127 Output level
L in
R in
L out
R out
Step Pan
Step Pan
L in
R in
L out
R out
Slicer
Slicer
JUNO-G_e.book 136 ページ ２００６年２月１３日 月曜日 午後２時４４分