Filter
Top Products
48
Creating a Patch
OUTPUT
For details regarding effect settings, refer to the pages shown below.
•
Making Effect Settings
(p. 125)
•
Making Multi-Effects Settings (MFX1–3)
(p. 129)
•
Making Chorus Settings
(p. 154)
•
Making Reverb Settings
(p. 155)
Parameter
Value Explanation
Patch Out Assign
MFX,
A, B, 1–
4,
TONE
Specifies how the direct sound of each patch will be output.
MFX:
Output in stereo through multi-effects. You can also apply chorus or reverb to the sound that passes through multi-ef-
fects.
A, B:
Output to the OUTPUT A (MIX) jacks or OUTPUT B jacks in stereo without passing through multi-effects.
1–4:
Output to the INDIVIDUAL 1–4 jacks in mono without passing through multi-effects.
TONE:
Outputs according to the settings for each tone.
* If you’ve made settings so that sounds are separately routed to the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, but no plug is actually
inserted in the INDIVIDUAL 2 jack, the sounds routed to INDIVIDUAL 1 and INDIVIDUAL 2 will be mixed and output from the IN-
DIVIDUAL 1 jack.
* If the Mix/Parallel parameter is set to “MIX,” all sounds are output from the OUTPUT A (MIX) jacks in stereo (p. 158).
Tone Out Assign
MFX,
A, B, 1–
4
Specifies how the direct sound of each tone will be output.
MFX:
Output in stereo through multi-effects. You can also apply chorus or reverb to the sound that passes through multi-ef-
fects.
A, B:
Output to the OUTPUT A (MIX) jacks or OUTPUT B jacks in stereo without passing through multi-effects.
1–4:
Output to the INDIVIDUAL 1–4 jacks in mono without passing through multi-effects.
* If the Patch Out Assign is set to anything other than “TONE,” these settings will be ignored.
* When the Structure Type parameter has a setting of Type “2”–”10,” the outputs of tones 1 and 2 will be combined with tone 2, and the
outputs of tones 3 and 4 will be combined with tone 4. For this reason, tone 1 will follow the settings of tone 2, and tone 3 will follow the
settings of tone 4 (p. 35).
* If you’ve made settings so that sounds are separately routed to the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, but no plug is actually
inserted in the INDIVIDUAL 2 jack, the sounds routed to INDIVIDUAL 1 and INDIVIDUAL 2 will be mixed and output from the IN-
DIVIDUAL 1 jack.
* If the Mix/Parallel parameter is set to “MIX,” all sounds are output from the OUTPUT A (MIX) jacks in stereo (p. 158).
* If you’ve set Tone Out Assign to “MFX,” set the MFX Output Assign parameter (p. 127) to specify the output destination of the sound
that has passed through the multi-effects.
* Sounds are output to chorus and reverb in mono at all times.
* The output destination of the signal after passing through the chorus is set with the Chorus Output Select and Chorus Output Assign pa-
rameters (p. 127).
* The output destination of the signal after passing through the reverb is set with the Reverb Output Assign parameter (p. 127).
Tone Out Level
0–127 Level of the signal that is sent to the output destination specified by Tone Output Assign
Send Level (Output = MFX)
Tone Chorus Send
0–127 Level of the signal sent to chorus for each tone if the tone is sent through MFX
Tone Reverb Send 0–127 Level of the signal sent to reverb for each tone if the tone is sent through MFX
Send Level (Output = non MFX)
Tone Chorus Send
0–127 Level of the signal sent to chorus for each tone if the tone is not sent through MFX
Tone Reverb Send 0–127 Level of the signal sent to reverb for each tone if the tone is not sent through MFX
Setting Effects for a Patch (Effects/MFX/MFX Control/Chorus/Reverb)
JUNO-G_e.book 48 ページ ２００６年２月１３日 月曜日 午後２時４４分