Filter
Top Products
138
If an incorrect operation is performed, or if processing could not be performed as you speci ed, an error message will appear.
Refer to the explanation for the error message that appears, and take the appropriate action.
Message Meaning Action
Battery Low! The battery has run down. Recharge the batteries, or use an AC adaptor.
Cannot Erase! If only step 1 remains, no further steps can be erased. No further steps can be erase.
Cannot Insert! You can arrange sequences of up to 99 steps. No further steps can be insert.
Cannot Undo!
You have tried to operate the undo function though
there was no history of edit operations.
Cannot use the undo function.
Event Full!
The JUNO-Gi has used up all the events that can be
handled by one song.
Perform the Song Optimize operation (p. 104).
What is an event?
The smallest unit of memory used by the JUNO-Gi to store recorded results on a memory card is the event. A newly created
song provides approximately 2,000 events per song. For each track, one recording pass uses two events. Operations such as
punch-in/out or track copy also use up events. The number of events that are used up will uctuate in a complex way. Even if
there is capacity remaining on the memory card, further recording or track editing will not be possible if all of the events are
used up. In such cases, an error message such as “Event Full” will appear.
EMPTY
or
File Not Found!
The le was not found in SD card/USB memory. Make sure that the le exists on the SD card or in USB memory.
If when importing an audio le, the audio le was not
found in the SD card’s “/ROLAND/IMPORT” folder.
Place the audio le in the “/ROLAND/IMPORT” folder (p. 101).
Incorrect File!
This is a le that the JUNO-Gi is unable to play. Do not use this le.
If when importing an audio le, you attempted to
import a WAV/AIFF le of a format that is not supported
by the JUNO-Gi, the error message “Incorrect File!” will
appear, and the import cannot be performed.
Use a WAV/AIFF le that complies with the guidelines on p. 101.
The format of an SMF you intend to import to an
arpeggio style or rhythm pattern must be Format 0.
Make sure that the SMF you’re importing is in Format 0.
The SMF you attempted to import cannot be loaded
into the JUNO-Gi.
SMF data that contains a time signature other than the time signature
speci ed in the “Pattern Beat” (p. 124) setting cannot be loaded by the
JUNO-Gi. You need to change the time signature data of the SMF.
MIDI Bu er Full!
An unusually large amount of MIDI data was received,
and could not be processed.
Reduce the amount of MIDI messages that are being transmitted.
MIDI O ine! The MIDI IN connection was broken.
Check that there is no problem with the MIDI cable connected to the
JUNO-Gi’s MIDI IN, and that the MIDI cable was not disconnected.
No Data! The track data you are trying to export was not found. Select the track where track data exists.
No Song!
There are no songs on the SD card. Create a new song (p. 91).
Incorrect data is in the song folder, or the necessary data
is not present.
Restore the data backed up on the computer to the JUNO-Gi. In this
case, restore each “ROLAND” folder to the JUNO-Gi (p. 79).
Now Playing! The Song Player/Digital Recorder is currently playing. Either stop playback, or wait until playback has ended.
Now Recording! The Digital Recorder is currently recording. Either stop record, or wait until record has ended.
Pattern Full!
The rhythm pattern cannot be recorded any further
because you have exceeded the maximum number of
notes recordable in a single rhythm pattern.
Delete unneeded data from the rhythm pattern you’re recording.
SD Card Busy!
Since the data on the SD card is stored in a fragmented
state, it is taking too long to read/write the data.
Alternatively, you’re using an SD card whose processing
speed is too slow.
This is more likely to occur if you’ve been using
operations such as track editing and punch-in/out
recording to connect phrases (recorded data) several
seconds in length.
Reduce the number of tracks being played back simultaneously. You can
use bouncing to combine tracks, erase and then delete data of tracks
you’re not playing back, and then play back.
Reduce the number of tracks being recorded simultaneously.
SD Card Full!
There is insu cient free space on the SD card.
Use an SD card that has su cient free space.
Delete unneeded songs (p. 103).
Increase the free space on the SD card by executing the Song Optimize
command to delete unneeded data from the card (p. 104).
The number of songs has exceeded 99.
A maximum of 99 songs can be saved on an SD card. Delete unneeded
songs (p. 103).
Error Message List