Filter
Top Products
82
Parameter Value Explanation
Continuous
Hold
OFF, ON
Determines whether the HOLD PEDAL jack
will provide support for half-pedaling (ON),
or not (OFF). When this is set to support
use of half-pedaling techniques, you can
then connect an optional expression pedal
(DP-10, etc.), and employ pedal work to
achieve even ner control in performances
in which piano tones are used.
[3] ( CTRL)
Parameter Value Explanation
Sys Ctrl 1–4
Source
Selects the MIDI message used as the System Control.
OFF The system control knob will not be used.
CC01–31, 33–95 Controller numbers 1–95
PITCH BEND Pitch Bend
AFTERTOUCH Aftertouch
Source Select
SYSTEM
“Sys Ctrl 1–4 Source” settings will be used
for tone control.
LIVE SET
“Tone Ctrl 1–4 Source” (p. 38) settings of each
Live Set will be used for tone control.
System Menu [3] ( MIDI/SYNC)
[1] ( GENERL)
Parameter Value Explanation
Local Switch OFF, ON
Determines whether the internal sound generator
is disconnected (OFF) from the controller section
(keyboard, pitch bend/modulation lever, knobs,
buttons, D Beam controller, pedal, and so on); or not
disconnected (ON).
Normally this is left “ON,” but if you wish to use the
JUNO-Gi’s keyboard and controllers to control only
external sound modules, set it to “OFF.”
Device ID 17–32
When you want to transmit or receive System
Exclusive messages, set this parameter to match the
Device ID number of the other MIDI device.
Remote
Keyboard
Switch
OFF, ON
Set this parameter “ON” when you want to use an
external MIDI keyboard instead of the JUNO-Gi’s
keyboard. In this case, the MIDI transmit channel
of the external MIDI keyboard can be set to any
channel. Normally you will leave this parameter
“OFF.”
* Turn this “ON” when you want to control the
JUNO-Gi from an external MIDI device when
performing with the Arpeggio function.
Main Channel 1–16
MIDI receive channel for playing the JUNO-Gi from
an external MIDI device.
Sub Channel 1–16
MIDI receive channel on which an external MIDI
device can play the JUNO-Gi’s Lower layer when the
[SPLIT] button is on.
USB MIDI
USB-MIDI
Thru
OFF, ON
If this is “ON,” incoming MIDI messages will be
re-transmitted without change from the MIDI OUT
connector.
Using the Local Switch
When you’re using the JUNO-Gi with external sequencer software, leave the
Local Switch turned o . Read the following for details.
Typically, things are hooked up so the data travels as follows: the JUNO-Gi’s
keyboard g your external sequencer software g the JUNO-Gi’s sound
generator. Normally, the JUNO-Gi’s keyboard section is internally connected to
its sound generator section; this internal connection is controlled by the Local
Switch. If you turn the Local Switch o , the JUNO-Gi’s keyboard and sound
generator sections will be independent, allowing you to use the connection
described with your external sequencer software.
Connecting the JUNO-Gi to an external sequencer
JUNO-Gi Keyboard
(External) Sequencer
Local O
JUNO-Gi
Sound Generator
[2] ( TX)
Parameter Value Explanation
Transmit
Program Change
OFF, ON
Speci es whether Program Change messages
will be transmitted (ON) or not (OFF).
Transmit Bank
Select
OFF, ON
Speci es whether Bank Select messages will
be transmitted (ON) or not (OFF).
Transmit Active
Sensing
OFF, ON
Speci es whether Active Sensing messages
will be transmitted (ON) or not (OFF).
Transmit Edit
Data
OFF, ON
Specify whether changes you make in the
settings of a patch, performance will be
transmitted as system exclusive messages
(ON), or will not be transmitted (OFF).
Soft Through OFF, ON
Thru function re-transmits all messages
received at the MIDI IN connector to the MIDI
OUT connector without modifying them in
any way.
[3] ( RX)
Parameter Value Explanation
Receive Program
Change
OFF, ON
Speci es whether Program Change messages
will be received (ON) or not (OFF).
Receive Bank
Select
OFF, ON
Speci es whether Bank Select messages will
be received (ON) or not (OFF).
Receive Exclusive OFF, ON
Speci es whether System Exclusive messages
will be received (ON) or not (OFF).
Receive GM
System On
OFF, ON
Speci es whether General MIDI System On
messages will be received (ON) or not (OFF).
Receive GM2
System On
OFF, ON
Speci es whether General MIDI 2 System On
messages will be received (ON) or not (OFF).
Receive GS Reset OFF, ON
Speci es whether GS Reset messages will be
received (ON) or not (OFF).