Filter
Top Products
38
LIVE SET EDIT 3 Screen
[1] (COMMON)
Parameter Value Explanation
LiveSet Category Type (category) of the live set
LiveSet Tempo 20–250 Tempo of the live set
Common Level 0–127 Adjusts the volume of the entire live set.
Common Cuto
oset
-64–+63
Adjusts the cuto frequency of the entire live
set.
You can use the SOUND MODIFY [CUTOFF] knob
to control this (p. 29).
Common
Resonance oset
-64–+63
Adjusts the resonance of the entire live set.
You can use the SOUND MODIFY [CUTOFF] knob
to control this (p. 29).
Phase Lock OFF, ON
Set to “ON” when you want to suppress
discrepancies in timing of parts played on the
same MIDI channel.
* When this parameter is set to “ON,”
parts on the same MIDI channel are
put in a condition in which their
timing is matched, enabling them
to be played at the same time.
Accordingly, a certain amount of time
may elapse between reception of the
Note messages and playing of the
sounds. Turn this setting to “ON” only
as needed.
Preview Type
Type of phrase played back when you press the [PREVIEW]
button
* Valid only if the System setting “Preview Mode” (p.
80) is set to “PHRASE.”
SINGLE A single phrase for Upper and Lower
RHYTHM
A phrase for a rhythm set
MULTI Dierent phrases for Upper and Lower
Preview Phrase
Phrase that is played back when you press the [PREVIEW]
button
Preview Octave -3–+3 Pitch of the preview phrase (in octave steps)
[2] (CONTROL)
Parameter Value Explanation
Split Setting
Split Switch OFF, ON Species the Split setting (p. 26).
Split Point OFF, C#-–G9 Species the Split Point (p. 26).
Arpeggio
Destination
Species the layer played by the arpeggio.
UPPER
The Upper layer will be played by the
arpeggio.
LOWER
The Lower layer will be played by the
arpeggio.
BOTH
The Upper and Lower layers will be
played by the arpeggio.
* If Split is on, the Upper layer
will be played by the arpeggio.
Tone Control Source
Tone Ctrl 1–4
Source
Selects the MIDI message used as the tone Control.
OFF The tone control will not be used.
CC01–31, 33–95 Controller numbers 1–31, 33–95
PITCH BEND Pitch Bend
AFTERTOUCH Aftertouch
Parameter Value Explanation
Assignable Switch
Switch 1/Switch 2
Assign
The function assigned to the [S1], [S2] buttons
TRANSPOSE UP
Shift the pitch of the keyboard upward
in semitone steps (a maximum of six
semitones).
TRANSPOSE
DOWN
Shift the pitch of the keyboard down-
ward in semitone steps (a maximum of
ve semitones).
TAP TEMPO
Used to set the keyboard tempo to the
interval at which you press the button.
MONO/POLY
Specify whether the tone will play
polyphonically (POLY) or monophoni-
cally (MONO).
PORTAMENTO Turn the Portamento on/o.
HOLD Turn the Hold on/o.
MFX1, 2 SW Switch the multi-eects 1–2 on/o.
CHORUS SW Switch the chorus on/o.
REVERB SW Switch the reverb on/o.
SYS CTRL 1–4 SRC
Transmit the MIDI message specied by
the System setting “Sys Ctrl 1–4 Source.”
LAYER 1 SW (U1)
LAYER 2 SW (U2)
LAYER 3 SW (L1)
LAYER 4 SW (L2)
Turns the Layer Switch On/O for the
specied layer
Switch 1/Switch
2 Type
The way in which the [S1], [S2] buttons will operate when
pressed.
* Depending on the Assign setting, this may not be
available.
LATCH
The on/o status will alternate each time
you press the button.
MOMENTARY
The assigned function will turn on while
you press the button, and will turn o
when you release it.