Filter
Top Products
146
23) Load .KMP: selected icon
The selected .KMP file will be loaded as a multisample. The
.KSF files used by the .KMP will also be loaded as samples.
The .KSF files used by the .KMP file will be saved in
an identically-named directory that is created auto-
matically when the .KMP file is created.
1 To load the data, press the [F8] (“OK”) key. To cancel
without loading, press the [F7] (“Cancel”) key.
The data will be loaded into the numbers that follow the
last multisample or sample number currently existing in
sample data RAM (i.e., that were previously sampled or
loaded). In this case, only the valid multisamples and
samples will be loaded (Append load).
If a .KSF file used by the .KMP file is not found in the cur-
rent directory or lower, a dialog box will appear, asking
you to specify the directory. Use the procedure described
in “When a file to be loaded cannot be found...” (
☞p.141)
to load the required .KSF file.
Since overflow checking of sample data RAM is per-
formed when loading each individual .KSF file, it is
possible that an overflow may occur in the middle of
the loading process.
You can load multiple files within the directory.
(
☞p.145)
24) Load .KSF: selected icon
The selected .KSF file will be loaded as a sample.
1 To load the data, press the [F8] (“OK”) key. To cancel
without loading, press the [F7] (“Cancel”) key.
The data will be loaded into the numbers that follow the
last sample number currently existing in sample data
RAM (i.e., that were previously sampled or loaded)
(Append load).
You can load multiple files within the directory.
(
☞p.145)
Loading AIFF files and WAVE files
If the EXB-SMPL option (sold separately) and sample data
RAM are installed in the TRITON Le, you can load AIFF for-
mat or WAVE format files containing audio data that was
saved on your computer. The loaded data can be used as
samples or drum samples.
25) Load .AIF: selected icon
The selected AIFF file will be loaded as a sample.
1 To load the data, press the [F8] (“OK”) key. To cancel
without loading, press the [F7] (“Cancel”) key.
The data will be loaded into the numbers that follow the
last sample number currently existing in sample data
RAM (i.e., that were previously sampled or loaded)
(Append load).
You can load multiple files within the directory.
(
☞p.145)
26) Load .WAV: selected icon
The selected WAVE file will be loaded as a sample.
1 To load the data, press the [F8] (“OK”) key. To cancel
without loading, press the [F7] (“Cancel”) key.
The data will be loaded into the numbers that follow the
last sample number currently existing in sample data
RAM (i.e., that were previously sampled or loaded)
(Append load).
Files with an extension of other than .AIF/.WAV cannot
be recognized as AIFF/WAVE files. In this case, use the
Utility “Rename” (1.1–3a) to change the last four char-
acters of the filename to “.AIF”/“.WAV”
If the data that is loaded as a sample contains a loop
point, you can set “S.Ofs(Start Offset)” (PROG 2.1–2b,
GLOBAL 5.1–1b) on the TRITON Le so that the sound
will begin from the loop point.
If data whose sample size is 8 bits or less is loaded, it
will be converted into 16 bit data inside the TRITON Le.
This will mean that the amount of internal memory
consumed will be approximately twice as large as the
file size. The increase in size resulting from this conver-
sion may mean that it is impossible to save that data on
a media.
Loading AKAI S1000/S3000 format Sample files and
Program files
If sample data RAM is installed in the TRITON Le, AKAI
S1000/S3000 format Sample files and Program files can be
loaded (
☞p.147 “About AKAI Program files” for more infor-
mation about compatibility). The loaded Sample or Program
file data can be used as a sample or multisample respec-
tively. When the loaded data is then saved to storage media,
it will be saved as a Korg format .KSF file or .KMP file
respectively.
AKAI S1000/S3000 format stereo Sample files and Program
files whose names end in “-L” and “-R” can be loaded into
the TRITON Le as stereo samples and multisamples.
When the above files are loaded, “-L” and “-R” will auto-
matically be moved to the end of the sample name or multi-
sample name (15th and 16th character) so that they can
automatically be recognized as stereo samples or multisam-
ples.
27) Load AKAI Sample File: selected icon
The selected Sample will be loaded as a sample.
1 To load the data, press the [F8] (“OK”) key. To cancel
without loading, press the [F7] (“Cancel”) key.
The data will be loaded into the numbers that follow the
last sample number currently existing in sample data
RAM (i.e., that were previously sampled or loaded)
(Append load). If the loaded data is then saved to storage
media, it will be saved as a Korg format .KSF file. (possi-