Filter
Top Products
PROG
1.1
2.12.23.14.14.25.15.25.36.17.17.2
PROG
1.1
2.12.23.14.14.25.15.25.36.17.17.2
25
Latch* [Off, On]
Specifies whether or not the arpeggio will continue playing
after you take your hand off the keyboard.
On (checked): The arpeggio will continue playing after you
remove your hand from the keyboard.
Off (unchecked): The arpeggio will stop when you remove
your hand from the keyboard.
Key Sync.* [Off, On]
Specifies whether the arpeggio pattern will begin when you
press a key, or whether it will always follow the “ (Tempo)”
setting.
On (checked): The arpeggio pattern will start playing from
the beginning when a note-on occurs from a condition
where no keys are pressed. This setting is suitable when you
are playing in realtime and want the arpeggio to play from
the beginning of the measure.
Off (unchecked): The arpeggio pattern will always play
according to the “ (Tempo) .”
Keyboard* [Off, On]
This specifies whether the notes you play on the keyboard
will be sounded as usual in addition to being sounded as
part of the arpeggio.
On (checked): The notes you play will be sounded on their
own, in addition to being sounded as part of the arpeggio.
For example if you simultaneously press two or more notes,
they will be sounded as usual in addition to being played as
arpeggiated notes.
Off (unchecked): Only the arpeggiated notes will be heard.
* These parameters can also be set in “1.1–3: Arp.”
6.1–1b: Arpeggiator Tempo
(Tempo) [040...240, EXT]
Sets the tempo.
This can also be set by the REALTIME CONTROLS C-mode
[TEMPO] knob. When “MIDI Clock” (GLOBAL 2.1–1a) is
either External, this will indicate EXT, and the arpeggiator
will synchronize to MIDI Clock messages received from an
external MIDI device.
■ 6.1–1c: UTILITY
☞“Write Program” (1.1–1c)
For details on how to select the desired utility function, refer
to “PROG 1.1–1c: UTILITY.”
Copy Arpeggiator
This command copies arpeggio settings.
1 Select “Copy Arpeggiator” to access the dialog box.
2 In “From” specify the copy source arpeggio settings
(mode, bank, number).
3 If you are copying from Combination or Song, specify
whether you wish to copy from A or B.
4 To execute the Copy Arpeggio operation, press the [F8]
(“OK”) key. To cancel, press the [F7] (“Cancel”) key.
6.1–2: Zone (Scan Zone)
6.1–2a: Scan Zone
Zone Map
This shows the “Scan Zone” setting.
Key:
Btm (Bottom Key) [C–1...G9]
Top (Top Key) [C–1...G9]
These parameters specify the range of notes (keys) for which
the arpeggiator will function. “Top” is the upper limit, and
“Btm” is the lower limit.
Vel:
Btm (Bottom Velocity) [001...127]
Top (Top Velocity) [001...127]
Specifies the range of velocities for which the arpeggiator
will function. “Top” is the upper limit, and “Btm” is the
lower limit.
The note number and velocity can also be specified by
holding down the [ENTER] key and pressing a note on
the keyboard.
■ 6.1–2b: UTILITY
☞“Write Program” (1.1–1c), “Copy Arpeggiator” (6.1–1c)
6.1–2a
6.1–2b