Filter
Top Products
216
Amp LFO 1/2 Intensity (PROG 5.1–2b, 5.2)
The amp modulation intensity of LFO 1/2 can be controlled
by EG, keyboard tracking, controllers, or tempo etc.
• If you select EG as the “AMS (LFO1/2 AMS),” the depth
of the tremolo effect produced by LFO modulation will
change in synchronization with the changes in EG level.
If you set “Int. (AMS Intensity)” to a positive (+) value,
the tremolo effect will deepen as the EG level rises, and
lessen as the EG level falls. If “Int. (AMS Intensity)” is
set to a negative (–) value, the phase of the LFO will be
inverted.
• If select a controller such as SW1 or 2 as the “AMS
(LFO1/2 AMS),” you can apply the tremolo effect by
pressing the [SW1]or [SW2] key when desired.
Pan (PROG 5.1–1b)
The oscillator pan can be controlled by EG, LFO, keyboard
tracking, controllers, or tempo etc.
• If you select Note No. as the “AMS (Pan AMS)” and set
“Intensity” to +50, panning will be controlled by the
keyboard position: center at the C4 note, far right at C6
or above, and far left at C2 or below.
• If EG is selected as the “AMS (Pan AMS),” the oscillator
pan will be controlled in synchronization with the
changes in EG level. If “Intensity” is set to a positive (+)
value, the pan will move toward the right as the EG level
increases, and toward the left as the EG level decreases.
If “Intensity” is set to a negative (–) value, the opposite
effect will occur.
EG Level – Pitch EG (PROG 3.1–5b)
– Filter EG (PROG 4.1–5b)
– Amp EG (PROG 5.1–3b)
EG levels can be controlled by keyboard tracking, control-
lers, or tempo etc.
Set the “I (AMS Intensity)” value, and select +/–/0 for each
EG segment (“S” start, “A” attack, “B” break) to specify the
direction of the effect (if any) on that segment.
+: AMS will function according to the Intensity setting.
–: The sign of the Intensity setting will be inverted.
0: AMS will have no effect.
If “I (AMS Intensity)” is set to +66, the various EG levels can
be controlled over a maximum range of ±99.
• Set “AMS” to Velocity for Amp EG Level Modulation, “I
(AMS Intensity)” to +66, “S” to 0, “A” to +, and “B” to –.
Set all Amp EG levels to +00. As you play with
increasing velocity, the EG levels will change more
greatly. At the maximum velocity, the Start Level will
stay at +00, but the Attack Level will change to +99 and
the Break Level will change to –99.
EG Time – Pitch EG (PROG 3.1–5c)
– Filter EG (PROG 4.1–5c)
– Amp EG (PROG 5.1–3c)
EG times can be controlled by keyboard tracking, control-
lers, or tempo etc. Set the “I (AMS Intensity)” value, and
select +/–/0 for each EG segment (“A” attack, D” decay, “S”
slope, “R” release) to specify the direction of the effect (if
any) on that segment.
+: AMS will function according to the Intensity setting.
–: The sign of the Intensity setting will be inverted.
0: AMS will have no effect.
Each EG time is determined by the Alternate Modulation
value at the moment that the corresponding EG point is
reached. For example, the Alternate Modulation value at the
moment that the Attack Level is reached will determine the
Decay Time.
If “I (AMS Intensity)” is set to a value of 8, 17, 25, 33, 41, or
49, the corresponding time can be multiplied by a maximum
of 2, 4, 8, 16, 32, or 64 times (or divided by 1/2, 1/4, 1/8, 1/
16, 1/32, 1/64).
• Select JS+Y#01 for “AMS,” and set “I (AMS Intensity)”
to +8, “A” to +, “D” to –, and “S” and “R” to 0. When
you move the joystick in the +Y direction, the Attack
Time will be lengthened by a maximum of 2 times. The
Decay Time will be shortened by a maximum of 1/2.
The Slope and Release times will not change.
LFO Frequency (PROG 5.3–1b)
The frequency of LFO 1 or 2 can be controlled by EG, key-
board tracking, controllers, or tempo etc., You can even use
the LFO2 frequency to modulate the LFO1 frequency.
If “Int (AMS 1/2 Intensity)” is set to a value of 16, 33, 49, 66,
82, or 99, the corresponding frequency can be multiplied by
a maximum of 2, 4, 8, 16, 32, or 64 times (or divided by 1/2,
1/4, 1/8, 1/16, 1/32, 1/64).
• Select JS+Y#01 for “AMS1/2 (Freq. AMS1/2),” and set
“Int (AMS1/2 Intensity)” to +16. When you move the
joystick in the +Y direction, the LFO frequency will be
increased by a maximum of 2 times. If you set “Int
(AMS1/2 Intensity)” to –16 and move the joystick in the
+Y direction, the LFO frequency will be decreased by up
to 1/2.