Filter
Top Products
Effect
185
37: Detune
Using this effect, you can obtain a detune effect that offsets
the pitch of the effect sound slightly from the pitch of the
input signal. Compared to the chorus effect, a more natural
sound thickness will be created.
e: InLvl Mod, e: Src
This parameter sets the dynamic modulation of the input level.
38: Pitch Shifter
This effect changes the pitch of the input signal. You can select
from three types: Fast (quick response), Medium, and Slow
(preserves tonal quality). You can also create an effect in
which the pitch is gradually raised (or dropped) using the
delay with feedback.
a: Mode
This parameter switches the pitch shifter operating mode. With
Slow, tonal quality will not be changed too much. With Fast, the
effect becomes a Pitch Shifter that has a quick response, but may
change the tone. Medium is in between these two. If you do not
need to set too much pitch shift amount, set this parameter to
Slow. If you wish to change the pitch significantly, use Fast.
b: Shift, b: (Source), b: (Amount), c: Fine, c: (Amount)
The amount of pitch shift will use the value of the “Shift” plus the
“Fine” value. The amount of modulation will use the c: (Amount)
value plus d: “(Amount).”
Modulation Source is used both for “Shift” and “Fine.”
e: Feedback Position, f: Feedback
When “Feedback Position” is set to Pre, the pitch shifter output is
again input to the pitch shifter. Therefore, if you specify a higher
value for the Feedback parameter, the pitch will be raised (or low-
ered) more and more each time feedback is repeated.
If “Feedback Position” is set to Post, the feedback signal will not
pass through the pitch shifter again. Even if you specify a higher
value for the Feedback parameter, the pitch-shifted sound will be
repeated at the same pitch.
a
Sft (Pitch Shift)
Sets the pitch difference from the input signal
–100...+100cent
(Source)
Selects the modulation source of the pitch shift
Off...Tempo
(Amount)
Sets the modulation amount of the pitch shift
–100...+100cent
b
Delay (Delay Time)
Sets the delay time
0...1000ms
c
Feedback
Sets the feedback amount
–100...+100
d
High Damp
Sets the damping amount in the high range
0...100%
e
InLvl Mod (Input Level Dmod [%])
Sets the modulation amount of the input level
–100...+100
☞,
Src (Source)
Selects the modulation source for the input level
Off...Tempo
☞
f
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Input Level
Input Level
+
High Damp
Delay
Feedback
Detune
Input Level
Louder
Max
Zero
Higher
D
-mod
Input Level
Max
Zero
Higher
D
-mod
x1.0
x0.5
Amt= +100
Amt= +50
Louder
x1.0
x0.5
Amt= –100
Amt= –50
Input Level D-mod
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Input Level
Input Level
+
High Damp
Delay
Feedback
Pitch Shifter
Feedback Position
Pre
Post
a
Mode Slow, Medium, Fast
Switches Pitch Shifter mode ☞
b
Shift (Pitch Shift) –24...+24
Sets the pitch shift amount by steps of a semitone ☞,
(Source) Off...Tempo
Selects the modulation source of pitch shift amount ☞
(Amount)
Sets the modulation amount of pitch shift amount
–24...+24
☞
c
Fine
Sets the pitch shift amount by steps of a cent
–100...+100cent
☞,
(Amount)
Sets the modulation amount of pitch shift amount
–100...+100cent
☞
d
Delay (Delay Time)
Sets the delay time
0...1000ms
e
Feedback Position
Switches the feedback connection.
Pre, Post
☞
f
Feedback
Sets the feedback amount
–100...+100
☞
HiDamp (High Damp)
Sets the damping amount in the high range
0...100%
g
InLvl Mod (Input Level Dmod [%]) –100...+100
Sets the modulation amount of the input level ☞ Fx:37,
Src (Source)
Selects the modulation source for the input level
Off...Tempo
☞ Fx:37
h
W/D (Wet/Dly) Dry, 1:99...99:1, Wet
Sets the balance between the effect and dry sounds
(Source) Off...Tempo
Selects the modulation source of the effect balance
(Amount)
Sets the modulation amount of the effect balance
–100...+100