Filter
Top Products
COMBI
1.1
2.12.23.13.23.33.44.14.24.34.46.17.17.2
41
These settings allow you to apply filters to the MIDI data
that will be transmitted and received by each timbre 1–8. For
example even if two timbres are being played by the same
MIDI channel, you can make settings so that the damper
pedal will apply to one but not the other.
On (checked): Transmission and reception of MIDI data is
enabled.
When “Status” (3.1–1a) is INT, operations of the built-in
controllers or incoming MIDI data will apply the effect of
the checked item to the program of the corresponding tim-
bre. (The effect dynamic modulation function is not affected
by this setting.)
When “Status” is EXT or EX2, operations of the built-in con-
trollers will transmit MIDI data on the channel of that tim-
bre. MIDI transmission and reception settings for this
instrument are made in “MIDI Filter” (GLOBAL 2.1–1b).
The MIDI Filter 3 and MIDI Filter 4 pages contain MIDI fil-
ters for assignable controllers (whose function can be set by
the user), and if these are assigned to MIDI control changes,
the filter settings will affect those control changes.
In this case, if the assignable controllers have been set to
control changes that are also found in the MIDI Filter 1 or
MIDI Filter 2 pages, the settings in the MIDI Filter 1 and
MIDI Filter 2 pages will take priority. Also, if the same con-
trol change is assigned to two or more controllers in the
MIDI Filter 3 and MIDI Filter 4 pages, checking any one of
them will enable that control change.
Off (unchecked): Transmission and reception of MIDI data
is disabled.
4.1–1: MIDI 1–1 (MIDI Filter 1–1)
4.1–1a: Program Change, After Touch
Program Change [Off, On]
Specifies whether or not MIDI program change messages
will be transmitted and received.
After Touch [Off, On]
Specify whether or not MIDI after touch messages will be
transmitted and received.
■ 4.1–1b: UTILITY
☞“Write Combination,” “Solo Selected Timbre” (1.1–1c)
4.1–2: MIDI 1–2 (MIDI Filter 1–2)
4.1–2a: Damper CC#64, Portamento SW CC#65
Damper CC#64 [Off, On]
Specifies whether or not MIDI control change message #64
hold (damper pedal) messages will be transmitted and
received.
Portamento SW CC#65 [Off, On]
Specifies whether or not MIDI control change message #65
portamento on/off messages will be transmitted and
received.
■ 4.1–2b: UTILITY
☞“Write Combination,” “Solo Selected Timbre” (1.1–1c)
4.2–1: MIDI 2–1 (MIDI Filter 2–1)
4.2–1a: JS+Y CC#01, JS–Y CC#02
JS+Y CC#01 [Off, On]
Specifies whether or not MIDI control change #1 (the +Y axis
of this instrument’s joystick, or specified as the “B” assign-
ment of a REALTIME CONTROL knob) will be transmitted
or received.
JS–Y CC#02 [Off, On]
Specifies whether or not MIDI control change #2 (the –Y axis
of this instrument’s joystick, or specified as the “B” assign-
ment of a REALTIME CONTROL knob) will be transmitted
or received.
■ 4.2–1b: UTILITY
☞“Write Combination,” “Solo Selected Timbre” (1.1–1c)
COMBI 4.1: Ed–MIDI Filter1
4.1–1a
4.1–1b
COMBI 4.2: Ed–MIDI Filter2
4.1–2a
4.1–2b
4.2–1a
4.2–1b