Filter
Top Products
149
Editing Songs
Editing Songs
Extracting and Moving a Part of
Sequencer Data (Extract)
This function extracts a specified sequencer data area from a phrase
track or pattern and moves it to the same Song position of another
phrase track or pattern. Additionally, just as with Standard MIDI
File Format 0, when sequencer data from multiple MIDI channels is
recorded on one track, you can also assign one MIDI channel to a
single phrase track.
1. Access the Song Edit screen, and then load the song you
want to edit (p. 136).
2. Press [8 (Track Edit)].
The Track Edit window appears.
3. Press or to select “Extract,” and then press [8
(Select)].
A message of “EXTRACT: Select source point.” appears.
4. Use [CURSOR] to move the cursor to the first measure of the
track or pattern from which you want to extract sequencer
data.
5. Hold down [SHIFT] and press to move the cursor to the
last measure of the track or pattern from which you want to
extract sequencer data, and press [8 (Select)].
A message of “EXTRACT: Select destination point.” appears.
6. Use [CURSOR] to move the cursor to the track or pattern to
which the data will be moved, and press [8 (Select)] to
specify it. If you want to specify all tracks, press [7 (TrkAll)].
The Track Edit (Extract) window appears.
fig.11-24_50
7. Use [CURSOR] to move the cursor to the desired parameter,
and turn the VALUE dial or press [INC]/[DEC] to make the
setting. First check the region that is to be affected by the
operation, and correct it if necessary.
Track (Source Track)
Check/modify the phrase track or pattern from which the sequencer
data will be extracted. After Extract is executed, the selected
sequencer data no longer remains on this phrase track or pattern.
Value
TRK 1–TRK 16: The specified phrase track
PTN001–PTN100: The specified pattern
Measure, for (Edit Range)
Check/modify the range of measures from which sequencer data
will be extracted. If you set “for” to “ALL,” all measures will be
specified.
→ Track (Destination Track)
Check/modify the move-destination track or pattern.
Value
ALL: According to its MIDI channel, the sequencer data will be
divided among phrase tracks 1–16.
TRK 1–TRK 16: The specified phrase track
PTN001–PTN100: The specified pattern
Mode (Extract mode)
Specifies whether you want to keep the sequencer data at the
destination.
Value
MIX: The data at the destination will combine with the extracted
data.
REPLACE: The data at the destination will be erased and replaced
by the extracted data.
If you select “REPLACE,” only the sequencer data on the MIDI
channel specified by the Channel parameter will be the object of
the operation. Sequencer data of all other MIDI channels will be
unaffected.
Status
Selects the type of data to be extracted.
Value
ALL: All types of sequencer data
NOTE: Note
P.AFT: Polyphonic Aftertouch
C.C: Controller numbers
PROG: Program numbers
C.AFT: Channel Aftertouch
BEND: Pitch Bend
EXC: System Exclusive messages
Tune: Tune Request
PTN: Pattern Call Message data
Range
If you set the Status parameter to “NOTE,” “P.AFT,” “C.C,” or
“PROG,” specify the range of data. Specify the minimum value of
the range at the left, and the maximum value at the right.
• To extract all Note or Polyphonic Aftertouch data, specify “C-1–
G9.” To extract C4 Note/Polyphonic Aftertouch data, specify
“C4–C4.” To extract Note/Polyphonic Aftertouch data over the
range from C3 to C4, specify “C3–C4.”
• If you want to extract all controller numbers, set this to “0–127.”
If you want to extract all program numbers, set this to “1–
128.”To extract Controller/Program number 4, specify “4–4.” To
extract Controller/Program numbers from 3 to 14, specify “3–
14.”