Filter
Top Products
168
Adding Effects
Tone Select
Select the tone for which you want to make settings.
Value: 1–4
This parameter is Rhythm Key Select when a rhythm set is
being selected. You can select the rhythm tone (A0–C8) for
which you want to make settings.
Patch Output Assign
Specifies for each patch how the direct sound will be output.
Value:
MFX: Output in stereo through multi-effects. You can also apply
chorus or reverb to the sound that passes through multi-effects.
A, B: Output to the OUTPUT A (MIX) jack or OUTPUT B jack in
stereo without passing through multi-effects.
1–4: Output to the INDIVIDUAL 1–4 jacks in mono without passing
through multi-effects.
TONE: Outputs according to the settings for each tone.
• When the settings are such that signals are split and output from
the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, and no plug is
inserted in the INDIVIDUAL 2 jack, the sounds from
INDIVIDUAL 1 and INDIVIDUAL 2 are mixed together, then
output from the INDIVIDUAL 1 jack. This sound comprises the
sounds from the INDIVIDUAL 1 and 2 jacks.
• This parameter is Rhythm Output Assign when a rhythm set is
being selected. You can specifies for each rhythm set how the
direct sound will be output.
If the Mix/Parallel parameter (SYSTEM/General) is set to
“MIX,” all sounds are output from the OUTPUT A (MIX) jacks in
stereo (p. 179).
Tone Output Assign
Sets the direct sound’s output method for each tone.
Value:
MFX: Output in stereo through multi-effects. You can also apply
chorus or reverb to the sound that passes through multi-effects.
A, B: Output to the OUTPUT A (MIX) jack or OUTPUT B jack in
stereo without passing through multi-effects.
1–4: Output to the INDIVIDUAL 1–4 jacks in mono without passing
through multi-effects.
• If the Patch Output Assign ( ) is set to anything other than
“TONE,” these settings will be ignored.
• When the Structure Type parameter (PATCH/TMT) has a
setting of Type “2”–”10,” the outputs of tones 1 and 2 will be
combined with tone 2, and the outputs of tones 3 and 4 will be
combined with tone 4. For this reason, tone 1 will follow the
settings of tone 2, and tone 3 will follow the settings of tone 4 (p.
56).
• When the settings are such that signals are split and output from
the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, and no plug is
inserted in the INDIVIDUAL 2 jack, the sounds from
INDIVIDUAL 1 and INDIVIDUAL 2 are mixed together, then
output from the INDIVIDUAL 1 jack. This sound comprises the
sounds from the INDIVIDUAL 1 and 2 jacks.
If the Mix/Parallel parameter (SYSTEM/General) is set to
“MIX,” all sounds are output from the OUTPUT A (MIX) jacks in
stereo (p. 179).
• When setting the “MFX,” set the output destination with the
MFX Output Assign ( ) for the sound after it has passed
through the multi-effects.
• Chorus and reverb are output in mono at all times.
• The output destination of the signal after passing through the
chorus is set with the Chorus Output Select ( ) and the Chorus
Output Assign ( ).
• The output destination of the signal after passing through the
reverb is set with the Reverb Output Assign ( ).
Tone Dry Send Level
Set the level of the signal that is sent to the output destination
specified by Output Assign ( , ).
Value: 0–127
Tone Chorus Send Level
Sets the level of the signal sent to chorus for each tone.
Value: 0–127
Tone Reverb Send Level
Sets the level of the signal sent to reverb for each tone.
Value: 0–127
MFX Type (Multi-Effects Type)
Use this parameter to select from among the 90 available multi-
effects. For details on multi-effects parameters, refer to “Multi-
Effects Parameters” (Sound/Parameter List).
Value: 0 (Through)–90
MFX Dry Send Level (Multi-Effects Dry Send
Level)
Adjusts the volume of the sound that has passed through the multi-
effects.
Value: 0–127
MFX Chorus Send Level (Multi-Effects
Chorus Send Level)
Adjusts the amount of chorus for the sound that passes through
multi-effects. If you don’t want to add the Chorus effect, set it to “0.”
Value: 0–127
1
2
3
2
11
13
15
18
4
2 3
5
6
7
8
9