Filter
Top Products
151
Editing Songs
Editing Songs
Channel (MIDI Channel)
Selects the MIDI channel of the data to be shifted in time.
To shift clocks of all sequencer data, set this parameter to ALL. To
shift the sequencer data clock of just one specific MIDI channel,
select that MIDI channel.
Value: ALL, 1–16
If you set the Track parameter to “TEMPO,” or if the Status
parameter is set to “EXC,” “TUNE” or “PTN,” the Channel
parameter will not be available.
7. When you have finished making settings, press [8 (Execute)]
to execute the operation.
Thinning Out the Sequencer Data
(Data Thin)
Continuously variable controllers such as aftertouch, pitch bend, and
expression tend to create unexpectedly large amounts of data when
operated. Data Thin will strip out redundant data to increase the
amount of memory available for the sequencer.
1. Access the Song Edit screen, and then load the song you
want to edit (p. 136).
2. Press [8 (Track Edit)].
The Track Edit window appears.
3. Press or to select “Data Thin,” and then press [8
(Select)].
A message of “DATA THIN: Select target point.” appears.
4. Use [CURSOR] to move the cursor to the first measure of the
track or pattern whose sequencer data you want to thin. If
you want to specify all tracks, press [7 (TrkAll)].
5. Hold down [SHIFT] and press to move the cursor to the
last measure of the track or pattern whose sequencer data
you want to thin, and press [8 (Select)] to specify it.
The Track Edit (Data Thin) window appears.
fig.11-26_50
6. Use [CURSOR] to move the cursor to the desired parameter,
and turn the VALUE dial or press [INC]/[DEC] to make the
setting. First check the region that is to be affected by the
operation, and correct it if necessary.
Track
Check/modify the track(s) or pattern whose sequencer data will be
thinned.
Value
ALL: Phrase tracks 1–16, the beat track, and the tempo track
TRK 1–TRK 16: The specified phrase track
PTN001–PTN100: The specified pattern
Measure, for (Edit Range)
Check/modify the range of measures whose sequencer data will be
thinned. If you set “for” to “ALL,” all measures will be specified.
Value
For thinning data which incorporates rapid changes, use higher
settings. If you don’t want to thin that much data even though it is
subject to rapid change, use lower settings.
Time
If you are thinning data that changes gradually over time, use higher
settings. If you don’t want to thin that much data even though the
changes are gradual, use lower settings.
Status
Selects the type of data to be thinned.
Value
ALL: All following sequencer data types
P.AFT: Polyphonic Aftertouch
C.C: Controller numbers
C.AFT: Channel Aftertouch
BEND: Pitch Bend
Range
If you set the Status parameter to “P.AFT” or “C.C,” specify the
range of data. Specify the minimum value of the range at the left,
and the maximum value at the right.
• To thin all Polyphonic Aftertouch data, set “C-1–G9.” To thin C4
Polyphonic Aftertouch data, set “C4–C4.” To thin Polyphonic
Aftertouch data from C3 to C4, set “C3–C4.”
• To thin all Controller numbers, set “0–127.” To thin number 4,
set “4–4.” To thin numbers from 3 to 14, set “3–14.”
Channel (MIDI Channel)
Selects MIDI channel of the data to be thinned.
To thin all sequencer data, set this parameter to ALL. To thin
sequencer data of just one specific MIDI channel, select that MIDI
channel.
Value: ALL, 1–16
7. When you have finished making settings, press [8 (Execute)]
to execute the operation.