Filter
Top Products
172
Adding Effects
Part Select
Select the part for which you want to make settings.
Value: 1–16
Part Output Assign
Specifies for each part how the direct sound will be output.
Value
MFX: Output in stereo through multi-effects. You can also apply
chorus or reverb to the sound that passes through multi-effects.
A, B: Output to the OUTPUT A (MIX) jack or OUTPUT B jack in
stereo without passing through multi-effects.
1–4: Output to the INDIVIDUAL 1–4 jacks in mono without passing
through multi-effects.
PAT: The part’s output destination is determined by the settings of
the patch or rhythm set assigned to the part.
When the settings are such that signals are split and output from
the INDIVIDUAL 1 jack and INDIVIDUAL 2 jack, and no plug is
inserted in the INDIVIDUAL 2 jack, the sounds from
INDIVIDUAL 1 and INDIVIDUAL 2 are mixed together, then
output from the INDIVIDUAL 1 jack. This sound comprises the
sounds from the INDIVIDUAL 1 and 2 jacks.
If the Mix/Parallel parameter (SYSTEM/General) is set to
“MIX,” all sounds are output from the OUTPUT A (MIX) jacks in
stereo (p. 179).
• When setting the “MFX,” set the output destination with the
MFX Output Assign ( ) for the sound after it has passed
through the multi-effects.
• Chorus and reverb are output in mono at all times.
• The output destination of the signal after passing through the
chorus is set with the Chorus Output Select ( ) and the Chorus
Output Assign ( ).
• The output destination of the signal after passing through the
reverb is set with the reverb Output Assign ( ).
Part Output MFX Select (Part Output Multi-
Effects Select)
Of the three types of multi-effects that can be used simultaneously,
specify which multi-effects will be used.
Value: A–C (MFX-A–MFX-C)
Part Dry Send Level
Set the level of the signal that is sent to the output destination
specified by Part Output Assign ( ).
Value: 0–127
Part Chorus Send Level
Sets the level of the signal sent to chorus for each part.
Value: 0–127
Part Reverb Send Level
Sets the level of the signal sent to reverb for each part.
Value: 0–127
For the following parameters – , settings can be made
individually for each multi-effects (MFX1–MFX3) selected in
Part Output MFX Select ( ).
MFX Type (Multi-Effects Type)
Use this parameter to select from among the 90 available multi-
effects. For details on multi-effects parameters, refer to “Multi-
Effects Parameters” (Sound/Parameter List).
Value: 0 (Through)–90
Depending on the multi-effects you select here, it may not be
possible to use three multi-effects simultaneously.
MFX Dry Send Level (Multi-Effects Dry Send
Level)
Adjusts the volume of the sound that has passed through the multi-
effects.
Value: 0–127
MFX Chorus Send Level (Multi-Effects
Chorus Send Level)
Adjusts the amount of chorus for the sound that passes through
multi-effects. If you don’t want to add the Chorus effect, set it to “0.”
Value: 0–127
MFX Reverb Send Level (Multi-Effects
Reverb Send Level)
Adjusts the amount of reverb for the sound that passes through
multi-effects. If you don’t want to add the Reverb effect, set it to “0.”
Value: 0–127
MFX Output Assign (Multi-Effects Output
Assign)
Adjusts the output destination of the sound that has passed through
the multi-effects.
Value
A: Output to the OUTPUT A (MIX) jacks in stereo.
B: Output to the OUTPUT B jacks in stereo.
If the Mix/Parallel parameter (SYSTEM/General) is set to
“MIX,” all sounds are output from the OUTPUT A (MIX) jacks in
stereo (p. 179).
1
2
11
13
15
18
3
4
2
5
6
7 11
3
7
8
9
10
11