Filter
Top Products
53
Creating a Patch
Creating a Patch
BEND UP: Raises the pitch in semitone steps (up to 4 octaves
higher).
BEND DOWN: Lowers the pitch in semitone steps (up to 4 octaves
lower).
AFTERTOUCH: Aftertouch
OCT UP: Raises the key range in octave steps (up to 3 octaves
higher).
OCT DOWN: Lowers the key range in octave steps (up to 3 octaves
lower).
TRNS UP: Raises the key range in semitone steps (up to 6 semitones
higher).
TRNS DOWN: Lowers the key range in semitone steps (up to 5
semitones lower).
TAP TEMPO: Tap tempo (a tempo specified by the interval at which
you press the button).
MONO/POLY: Pressed to toggle between polyphonic (POLY) and
monophonic (MONO) play of a patch.
ARP HOLD: Switch between Hold On/Hold Off for the Arpeggiator
performance.
Mode 1–4 (Realtime Control Button Mode 1–4)
Specify how the [ ]–[ ] buttons are to operate.
Value
MOMENTARY: The button will be on only while you are pressing
(holding) it, and will be off when you release your finger from the
button.
LATCH: The button will switch on/off each time you press it.
D Beam
Switch (D Beam Switch)
Switches the D Beam controller on/off.
Value: OFF, ON
Assign (D Beam Assign)
Specifies the function controlled by the D Beam controller.
Value
OFF: The D Beam controller will not be used.
CC01–31, 33–95: Controller numbers 1–31, 33–95
For more information about Control Change messages, please
refer to “MIDI Implementation” (Sound/Parameter List).
BEND UP: Raises the pitch in semitone steps (up to 4 octaves
higher).
BEND DOWN: Lowers the pitch in semitone steps (up to 4 octaves
lower).
AFTERTOUCH: Aftertouch
NOTE: Play the sound of the most recently pressed key.
OCT UP: Raises the key range in octave steps (up to 3 octaves
higher).
OCT DOWN: Lowers the key range in octave steps (up to 3 octaves
lower).
START/STOP: Starts/Stops the sequencer.
TAP TEMPO: Tap tempo (a tempo specified by the interval at which
you move your hand over the D Beam controller).
ARP SWITCH: Switches the Arpeggiator on/off.
ARP VAR: Arpeggio Variation
ARP ACCENT: Arpeggio Accent Rate
ARP SHFFLE: Arpeggio Shuffle Rate
ARP OCT UP: The range in which the arpeggio is sounded will rise
in steps of an octave (maximum 3 octaves).
ARP OCT DW: The range in which the arpeggio is sounded will
lower in steps of an octave (maximum 3 octaves).
Polarity (D Beam Polarity)
Switch the polarity of the D Beam controller.
With a setting of “REVERSE,” the direction of control for the D Beam
controller will be inverted.
Range: STANDARD, REVERSE
Range Lower (D Beam Range Lower)
Specify the lower limit of the range of the D Beam controller. Values
below this setting will not be output.
Value: 0–UPPER
Range Upper (D Beam Range Upper)
Specify the upper limit of the range of the D Beam controller. Values
above this setting will not be output.
Value: LOWER–127
Setting Effects for a Patch (Effects/
MFX/MFX Control/Chorus/Reverb)
For details regarding effect settings, refer to the pages shown
below.
• “Applying Effects in Patch Mode” (p. 165)
• “Making Multi-Effects Settings (MFX/MFX Control)” (p. 174)
• “Making Chorus Settings (Chorus)” (p. 176)
• “Making Reverb Settings (Reverb)” (p. 177)