Filter
Top Products
Cho Rate (Chorus rate ) 0.05 - 10.0 [2]
Adjust the modulation speed of the chorus effect.
Cho Depth (Chorus depth ) 0 - 127 [3]
Adjust the modulation depth of the chorus effect.
+Cho Bal (Chorus balance ) D> 0E - D 0<E [5]
Adjust the volume balance between the direct
sound and the chorus sound. With a setting of “D>
0E,” only the direct sound will be output. With a set-
ting of “D 0<E,” only the chorus sound will be out-
put.
“D” or “E” on the display respectively means
D(direct sound) or E(effect sound) values of 100.
Dly Time (Delay time ) 0 - 500m [6]
Adjust the time delay from when the direct sound
begins until the delay sound is heard.
Dly Fb (Delay feedback level ) -98% - +98% [7]
Adjust the proportion (%) of the delay sound that is
fed back into the delay input. Negative (-) settings
will invert the phase.
Dly HF (Delay HF damp ) 315 - 8k/Bypass [8]
Adjust the frequency above which delayed sound
fed back to the delay input will be cut. If you do not
wish to cut the high frequencies of the feedback, set
this parameter to Bypass.
#Dly Bal (Delay balance ) D> 0E - D 0<E [10]
Adjust the volume balance between the sound
which passes through the delay and the sound
which does not. With a setting of D>0E, only the
chorus sound will be output, and with a setting of D
0<E, the chorus sound which passes through the
delay will be output.
“D” or “E” on the display respectively means
D(direct sound) or E(effect sound) values of 100.
Low Gain -12 - +12 [17]
Adjust the low frequency gain.
Hi Gain (High gain ) -12 - +12 [18]
Adjust the high frequency gain.
Level (Output level ) 0 - 127 [20]
Adjust the output level.
45: FL → Delay (Flanger → Delay) [02H, 0AH]
This effect connects a flanger and a delay in series.
FL Dly (Flanger pre delay ) 0 - 100m [1]
Adjust the time delay from when the direct sound
begins until the flanger sound is heard.
FL Rate (Flanger rate ) 0.05 - 10.0 [2]
Adjust the modulation speed of the flanger effect.
FL Depth (Flanger depth ) 0 - 127 [3]
Adjust the modulation depth of the flanger effect.
+FL Fb (Flanger feedback level )
-98% - +98% [4]
Adjust the proportion (%) of the flanger sound that
is fed back into the effect. Negative (-) settings will
invert the phase.
FL Bal (Flanger balance ) D> 0E - D 0<E [5]
Adjust the volume balance between the direct
sound and the flanger sound. With a setting of “D>
0E,” only the direct sound will be output. With a set-
ting of “D 0<E,” only the flanger sound will be out-
put.
“D” or “E” on the display respectively means
D(direct sound) or E(effect sound) values of 100.
Dly Time (Delay time ) 0 - 500m [6]
Adjust the time delay from when the direct sound
begins until the delay sound is heard.
Dly Fb (Delay feedback level ) -98% - +98% [7]
Adjust the proportion (%) of the delay sound that is
fed back into the delay input. Negative (-) settings
will invert the phase.
Dly HF (Delay HF damp ) 315 - 8k/Bypass [8]
Adjust the frequency above which delayed sound
fed back to the delay input will be cut. If you do not
wish to cut the high frequencies of the delay feed-
back, set this parameter to Bypass.
#Dly Bal (Delay balance ) D> 0E - D 0<E [10]
Adjust the volume balance between the sound
which passes through the delay and the sound
which does not. With a setting of D>0E, only the
flanger sound will be output, and with a setting of D
0<E, the flanger sound which passes through the
delay will be output.
“D” or “E” on the display respectively means
D(direct sound) or E(effect sound) values of 100.
Low Gain -12 - +12 [17]
Adjust the low frequency gain.
Hi Gain (High gain ) -12 - +12 [18]
Adjust the high frequency gain.
Level (Output level ) 0 - 127 [20]
Adjust the output level.
46: Cho → Flanger (Chorus → Flanger)
[02H, 0BH]
This effect connects a chorus and a flanger in series.
L
R
Delay
EQ
EQ
Flanger
L
R
Flanger
EQ
EQ
Chorus
Chapter 4. Insertion Effects
76