Filter
Top Products
#Dly Bal (Delay balance ) D> 0E - D 0<E [10]
Adjust the volume balance between the direct and
the delay sound.
“D” or “E” on the display respectively means
D(direct sound) or E(effect sound) values of 100.
Dly Pan (Delay Output Pan) L63 - 0 - R63 [18]
Adjust the stereo position of the delay sound. L63 is
far left, 0 is center, and R63 is far right.
Dly Level (Delay Level) 0 - 127 [19]
Adjust the volume of the delay sound.
Level (Output level ) 0 - 127 [20]
Adjust the output level.
58: Cho / Flanger (Chorus / Flanger) [11H, 02H]
This effect connects a chorus and a flanger in parallel.
Cho Dly (Chorus pre delay ) 0 - 100m [1]
Adjust the time delay from when the direct sound
begins until the chorus sound is heard.
Cho Rate (Chorus rate ) 0.05 - 10.0 [2]
Adjust the modulation speed of the chorus effect.
Cho Depth (Chorus depth ) 0 - 127 [3]
Adjust the modulation depth of the chorus effect.
+Cho Bal (Chorus balance ) D> 0E - D 0<E [5]
Adjust the volume balance between the direct and
the chorus sound.
“D” or “E” on the display respectively means
D(direct sound) or E(effect sound) values of 100.
Cho Pan (Chorus Output Pan) L63 - 0 - R63 [16]
Adjust the stereo position of the chorus sound. L63
is far left, 0 is center, and R63 is far right.
Cho Level (Chorus Level) 0 - 127 [17]
Adjust the volume of the chorus sound.
FL Dly (Flanger pre delay ) 0 - 100m [6]
Adjust the time delay from when the direct sound
begins until the flanger sound is heard.
FL Rate (Flanger rate ) 0.05 - 10.0 [7]
Adjust the modulation speed of the flanger effect.
FL Depth (Flanger depth ) 0 - 127 [8]
Adjust the modulation depth of the flanger effect.
FL Fb (Flanger feedback level ) -98% - +98% [9]
Adjust the proportion (%) of the flanger sound that
is fed back into the effect. Negative (-) settings will
invert the phase.
#FL Bal (Flanger balance ) D> 0E - D 0<E [10]
Adjust the volume balance between the direct and
the flanger sound.
“D” or “E” on the display respectively means
D(direct sound) or E(effect sound) values of 100.
FL Pan (Flanger Output Pan) L63 - 0 - R63 [18]
Adjust the stereo position of the flanger sound. L63
is far left, 0 is center, and R63 is far right.
FL Level (Flanger Level) 0 - 127 [19]
Adjust the volume of the flanger sound.
Level (Output level ) 0 - 127 [20]
Adjust the output level.
59: OD1 / OD2 (Overdrive / Distortion1,2)|
[11H, 03H]
This connects two effect units in parallel, each of
which allows you to select Overdrive or Distortion.
<OD1 (Overdrive/Distortion 1)>
OD1 Sel (OD1 Select) Odrv/Dist [1]
Select either Overdrive or Distortion for set 1.
+OD1 Drive (OD1 Drive) 0 - 127 [2]
Adjust the depth of distortion for set 1. The volume
will change together with the depth of distortion.
OD1 Amp (OD1 Amp Simulator Type)
Small/BltIn/2-Stk/3-Stk [3]
Select the type of guitar amp for set 1.
Small : small amp
BltIn : single-unit type amp
2-Stk : large double stack amp
3-Stk : large triple stack amp
L
R
Chorus
Flanger
Balance
Pan
Pan
L
R
Overdrive/
Distortion 2
Overdrive/
Distortion 1
Pan
Pan
Chapter 4. Insertion Effects
86