Filter
Top Products
Cho Dly (Chorus pre delay ) 0 - 100m [1]
Adjust the time delay from when the direct sound
begins until the chorus sound is heard.
Cho Rate (Chorus rate ) 0.05 - 10.0 [2]
Adjust the modulation speed of the chorus effect.
Cho Depth (Chorus depth ) 0 - 127 [3]
Adjust the modulation depth of the chorus effect.
+Cho Bal (Chorus balance ) D> 0E - D 0<E [5]
Adjust the volume balance between the direct
sound and the chorus sound. With a setting of “D>
0E,” only the direct sound will be output. With a set-
ting of “D 0<E,” only the chorus sound will be out-
put.
“D” or “E” on the display respectively means
D(direct sound) or E(effect sound) values of 100.
FL Dly (Flanger pre delay time ) 0 - 100m [6]
Adjust the time delay from when the direct sound
begins until the flanger sound is heard.
FL Rate (Flanger rate ) 0.05 - 10.0 [7]
Adjust the modulation speed of the flanger effect.
FL Depth (Flanger depth ) 0 - 127 [8]
Adjust the modulation depth of the flanger effect.
FL Fb (Flanger feedback level ) -98% - +98% [9]
Adjust the proportion (%) of the flanger sound that
is fed back into the effect. Negative (-) settings will
invert the phase.
#FL Bal (Flanger balance ) D> 0E - D 0<E [10]
Adjust the volume balance between the sound
which passes through the flanger and the sound
which does not. With a setting of D>0E, only the
chorus sound will be output, and with a setting of D
0<E, the chorus sound which passes through the
flanger will be output.
“D” or “E” on the display respectively means
D(direct sound) or E(effect sound) values of 100.
Low Gain -12 - +12 [17]
Adjust the low frequency gain.
Hi Gain (High gain ) -12 - +12 [18]
Adjust the high frequency gain.
Level (Output level ) 0 - 127 [20]
Adjust the output level.
❍ Effects that connect three or more types of
effect in series (series 3 / series 4 / series
5)
47: Rotary Multi [03H, 00H]
This connects Overdrive (OD), 3-band equalizer (EQ),
and Rotary (RT) effects in series.
+OD Drive 0 - 127 [1]
Adjust the depth of distortion. The volume will
change together with the depth of distortion.
OD Sw (Overdrive Switch) Off/On [2]
Turn the Overdrive effect on/off.
EQ L Gain (EQ Low Gain) -12 - +12 [3]
Adjust the low range gain of the equalizer.
EQ M Fq (EQ Mid Frequency) 200 - 6.3k [4]
Set the center frequency for the equalizer mid-
range.
EQ M Q (EQ Mid Q) 0.5/1.0/2.0/4.0/9.0 [5]
Adjust the width of the area centered at the EQ M
Fq setting in which the gain will be affected. The
area affected will become narrower as this value is
increased.
EQ M Gain (EQ Mid Gain) -12 - +12 [6]
Adjust the gain of the area specified by the EQ M
Fq parameter and the EQ M Q parameter.
EQ H Gain (EQ High Gain) -12 - +12 [7]
Adjust the high-range gain of the equalizer.
<RT (Rotary)>
RT L Slow (RT Low Frequency Slow Rate)
0.05 - 10.0 [8]
Adjust the speed of the low-range rotor for the low-
speed (Slow) setting.
RT L Fast (RT Low Frequency Fast Rate)
0.05 - 10.0 [9]
Adjust the speed of the low-range rotor for the high-
speed (Fast) setting.
RT Lo Accl (RT Low Frequency Accelaration)
0 - 15 [10]
Adjust the time over which the rotation speed of the
low-range rotor will change from low-speed to high-
speed (or high-speed to low-speed) rotation.
Smaller values will require greater time to reach the
new rotational speed.
RT Lo Lev (RT Low Frequency Level)0 - 127 [11]
Adjust the volume of the low-range rotor.
RT H Slow (RT High Frequency Slow Rate)
0.05 - 10.0 [12]
Adjust the speed of the high-range rotor for the low-
speed (Slow) setting.
L
R
Rotary
EQ
Over
drive
Chapter 4. Insertion Effects
77