Filter
Top Products
Troubleshooting
MOTIF XS Owner’s Manual
290
Appendix
Only one note sounds at a time.
■ When this situation occurs, the Mono/Poly parameter in the current mode is set to “mono.” If you wish to play chords, set this
parameter to “poly.”
Pitch or intervals are wrong.
■ Is the Master Tune parameter in the Utility mode set to a value other than “0”?
■ Is the Note Shift parameter in the Utility mode set to a value other than “0”?
■ When the voice produces a wrong pitch, is the appropriate tuning system selected from Micro Tuning parameter in the Voice Edit
mode?
■ When the Voice produces a wrong pitch, is the LFO Pitch Modulation Depth in the Voice Edit mode set too high?
■ When the Performance/Song/Pattern produces a wrong pitch, is the Note Shift parameter of each Part set to a value other than
“0”?
■ When the Song/Pattern playback produces a wrong pitch, is the Note Shift parameter in the Play FX display set to a value other
than “0”?
No effect is applied.
■ Is the [EFFECT BYPASS] button turned off? (page 13)
■ Have the REVERB and CHORUS knobs been turned fully counter-clockwise (to the minimum)?
■ Have any or all of the Elements’ Insertion Effect Output parameters been set to “thru” in the effect setting display in the Voice Edit
mode?
■ Have any or all of the effect types been set to “thru” or “off”?
■ When this occurs in the Performance mode/Song mode/Pattern mode, check whether the Insertion Switch (INS SW) parameters
are set properly or not.
The Edit Indicator appears, even when parameters are not being edited.
■ Keep in mind that even though the Edit mode is not active, simply moving a Knob/Slider or playing back the Song/Pattern
changes the current Voice, Performance, or Mixing, causing the Edit Indicator to appear.
Cannot start the Arpeggio.
■ Check whether the [ARPEGGIO ON/OFF] button is turned on or off.
■ Is the MIDI Sync parameter set to internal (using internal clock)?
■ When the User Arpeggio type is selected, does the currently selected Arpeggio actually contain data?
■ Are the Arpeggio related parameters such as Note Limit and Velocity Limit set appropriately?
[VOICE] → [F2] Porta → Mono/Poly Mode (page 93)
[PERFORM] → [EDIT] → Part selection → [F1] Voice → [SF1] Voice → Mono/Poly (page 152)
[SONG]/[PATTERN] → [MIXING] → [EDIT] → Part selection → [F1] Voice → [SF1] Voice → Mono/Poly (page 235)
[UTILITY] → [F1] General → [SF1] Play → Tune (page 259)
[UTILITY] → [F1] General → [SF1] Play → Note Shift (page 259)
[VOICE] → [EDIT] → [COMMON EDIT]→ [F1] General → [SF2] Play Mode → Bank, Tuning Number, Tuning Root (page 99)
[VOICE] → [EDIT] → Element/Key selection → [F5] Elm LFO → P Mod (page 125)
[PERFORM] → [EDIT] → Part selection → [F1] Voice → [SF1] Voice (page 151)
[SONG]/[PATTERN] → [MIXING] → [EDIT] → Part selection → [F1] Voice → [SF1] Voice (page 235)
[SONG]/[PATTERN] → [F2] Play FX → Note Shift (page 184)
[VOICE] → [EDIT] → [COMMON EDIT] → [F6] Effect → [SF1] Connect → Element Out 1-8 (page 108)
[PERFORM] → [EDIT] → [COMMON EDIT] → [F5] Effect → [SF2] InsSwitch (page 150)
[PERFORM] → [EDIT] → Part selection → [F1] Voice → [SF1] Voice (page 151)
[SONG]/[PATTERN] → [MIXING] → [F1] Part 1-16 → Ins FX Sw (page 232)
[SONG]/[PATTERN] → [MIXING] → [COMMON EDIT] → [F5] Effect → [SF2] Ins Switch (page 234)
[UTILITY] → [F5] Control → [SF2] MIDI → MIDI Sync = internal (page 268)
[VOICE] → [EDIT] → [COMMON EDIT] → [F2] ARP Main (page 101)
[PERFORM] → [EDIT] → Part selection → [F2] ARP Main (page 154)
[SONG]/[PATTERN] → [MIXING] → [EDIT] → Part selection → [F2] ARP Main (page 235)