Filter
Top Products
146
The D1200 won’t receive MMC
In the [SYSTEM/USB] “MIDI” tab page, is “RcvMMC”
turned “On”?
In the above page, is “MMC DevID” set to match the
MMC device ID setting of your MIDI sequencer? (→p.79,
102)
For some MIDI sequencers, the MMC device ID setting
may differ.
Is your MIDI sequencer set to transmit MMC?
→ Refer to the owner’s manual of your MIDI sequencer.
Can’t use MIDI to control effects or scenes
Are the D1200 and your MIDI sequencer set to the same
MIDI channel?
→ In the [SYSTEM/USB] “MIDI” tab page, check the “Glo-
balCh.” (→p.79, 101)
The D1200 does not synchronize as a slave
→ If the D1200 is set as an MTC slave, it may take several
seconds for synchronization to occur.
Can’t control another device via MMC
In the [SYSTEM/USB] “MMC” tab page, is “Select MMC
Mode” set to “Transmit”?
Is the MMC slave device set so that it will receive MMC?
The D1200 does not transmit mixer parameters
In the [SYSTEM/USB] “MIDI” tab page, is “Control-
Change” “Trans” turned “On”?
Is the device receiving the control changes set to record
each MIDI channel 1–12?
The D1200 does not receive mixer parameters
In the [SYSTEM/USB] “MIDI” tab page, is “Control-
Change” “Recv” turned “On”?
CD-R/RW
CD-R/RW drive option is not recognized
Is the CD-R/RW drive option installed correctly?
→ Turn off the power of the D1200, and check the connec-
tions. (→p.150)
Can’t write
No further data can be written to a CD-R/RW disc that
has been finalized. (→p.65, 76)
No data can be written to a CD-RW disc that contains
data written by another device.
Failed while writing to CD
→ Select a slower writing speed.
→ Use media that is recommended for your drive.
Some writing speeds cannot be selected when writing a
CD.
→ The speeds that you can select will depend on the type of
media and on the specifications of the CDRW-1. (→p.93)
Can’t play back on an audio CD player
Did you finalize the disc?
→ In the [CD] “CD-R/RW” tab page, press the “Final” but-
ton to finalize the disc. (→p.65)
Did you use CD-R media?
→ Some CD players are unable to play back CD-RW media.
We recommend that you use CD-R media.
Have you tried using a different type of media?
→ Even when the recommended media is used, some CD
players are unable to play back certain types of CD-R
media. You may be able to play back successfully if you
use a different type of CD-R media.
Can’t back up to CD-R/RW
Are you using blank media?
→ If using CD-R, you must use new (unused) media. If us-
ing CD-RW, go to the [CD] “CD-R/RW” tab page and
use the “Erase” button to erase the media before you ex-
ecute the backup operation.
WAV
Can’t preview
Is the WAV file in a supported format?
→ Select a WAV file of a format that the D1200 supports,
and preview it. (→p.71, 113)
USB
Computer does not recognize the D1200
Is the USB cable connected correctly? (→p.15)
Is the D1200 set to USB mode? (→p.77)
Error occurred when you disconnected the D1200 from the
computer
Use the correct procedure to disconnect. (→p.77)
When you connected the D1200, the computer asked you to
install software or a device driver
Does the operating system of your computer support the
D1200? (→p.77)