Filter
Top Products
254
D2A0
H
to D2B0
H
Network module failure
• A malfunction may have occurred due to noise. Check the wire and cable
distances and grounding condition of each device, and take measures
against noise.
• Execute hardware and self-loopback tests. If a failure occurs again, the
hardware of the master/local module may be faulty. Please consult your
local Mitsubishi representative.
D602
H
to D609
H
Parameter error
• Write the network parameters to the CPU module again.
• If this error persists, please consult your local Mitsubishi representative.
D60A
H
Parameter error (link scan
mode/constant link scan time setting
error)
• Write the network parameters to the CPU module again.
• Set "Asynchronous" to the link scan mode, or do not set the constant link
scan time.
• If this error persists, please consult your local Mitsubishi representative.
D60D
H
to D610
H
Network module failure
• A malfunction may have occurred due to noise. Check the wire and cable
distances and grounding condition of each device, and take measures
against noise.
• Execute hardware and self-loopback tests. If a failure occurs again, the
hardware of the master/local module may be faulty. Please consult your
local Mitsubishi representative.
D611
H
Parameter error (device range
assignment error (RWw))
• Write the network parameters to the CPU module again.
• Correct the value in the size of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
D612
H
Parameter error (device range
assignment error (RWw))
• Write the network parameters to the CPU module again.
• Correct the value in the offset of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
D613
H
Parameter error (device range
assignment error (RWr))
• Write the network parameters to the CPU module again.
• Correct the value in the size of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
D614
H
Parameter error (device range
assignment error (RWr))
• Write the network parameters to the CPU module again.
• Correct the value in the offset of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
D615
H
Parameter error (device range
assignment error (RY))
• Write the network parameters to the CPU module again.
• Correct the value in the size of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
D616
H
Parameter error (device range
assignment error (RY))
• Write the network parameters to the CPU module again.
• Correct the value in the offset of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
D617
H
Parameter error (device range
assignment error (RX))
• Write the network parameters to the CPU module again.
• Correct the value in the size of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
D618
H
Parameter error (device range
assignment error (RX))
• Write the network parameters to the CPU module again.
• Correct the value in the offset of the link device in the slave station(s)
(setting data), and retry the operation.
• If this error persists, please consult your local Mitsubishi representative.
D619
H
to D61A
H
Parameter error
• Write the network parameters to the CPU module again.
• If this error persists, please consult your local Mitsubishi representative.
Error code Error Action