Filter
Top Products
143
Global
P0
P1 P2 P3 P4 P5 P6
Unchecked (Local Control Off): The TRITON STUDIO’s
keyboard and joystick etc. will be disconnected from the
internal tone generator.
This means that operating the TRITON STUDIO (playing its
keyboard and using the joystick, or playing back the
sequencer) will not sound its internal tone generator.
Uncheck this setting if echo-back from an external sequencer
causes notes to be sounded in duplicate.
Even if this setting is unchecked, MIDI transmission
and reception will occur normally. Playing the key-
board will cause the corresponding note data to be
transmitted, and received note data will sound the TRI-
TON STUDIO’s internal tone generator.
Note Receive (Note Receive Filter) [All, Even, Odd]
This setting specifies whether even-numbered, odd-num-
bered, or all note numbers will be sounded when note data
is received from the TRITON STUDIO’s keyboard or from
an external MIDI device. By connecting the TRITON STU-
DIO to another TRITON STUDIO and setting one instru-
ment to Even and the other to Odd, you can effectively
double the polyphony by dividing the notes between the
two instruments.
All: All note numbers will be received. Normally you will
leave this set to All.
Even: Even-numbered notes (C, D, E, F#, G#, A#) will sound.
Odd: Odd-numbered notes (C#, D#, F, G, A, B) will sound.
This setting has no effect on the MIDI data that is
received.
Convert Position [PreMIDI, PostMIDI]
This setting specifies the location at which the Transpose,
Velocity Curve, and After Touch Curve settings will be
applied. This setting will affect the MIDI data that is trans-
mitted and received, and the data that is recorded on the
internal sequencer.
When using the TRITON STUDIO’s keyboard to play the
internal tone generator, the Transpose, Velocity Curve, and
After Touch Curve settings will always take effect regardless
of this setting.
PreMIDI: Velocity Curve, After Touch Curve, and Trans-
pose will be applied to the data that is transmitted from the
TRITON STUDIO’s keyboard.
This means that the Velocity Curve, After Touch Curve, and
Transpose settings will affect the data that is transmitted
from MIDI OUT when the TRITON STUDIO’s keyboard is
played, and the data that is recorded on the internal
sequencer. MIDI data received from MIDI IN or the data
played back by the internal sequencer will not be affected.
PostMIDI: Velocity Curve, After Touch Curve, and Trans-
pose will be applied to data before it enters the tone genera-
tor.
This means that the Velocity Curve, After Touch Curve, and
Transpose settings will affect the data that is sent to the
internal tone generator when you play the TRITON STU-
DIO’s keyboard, when the internal sequencer is played
back, or when data is received from MIDI IN.
This setting will not affect the data that is transmitted from
MIDI OUT or recorded on the internal sequencer when you
play the TRITON STUDIO’s keyboard or playback the
sequencer.
MIDI Clock (MIDI Clock Source)
[Internal, External MIDI, External mLAN]
Sets this parameter when you wish to synchronize an exter-
nal MIDI device (sequencer or rhythm machine etc.) with
the TRITON STUDIO’s internal arpeggiator or sequencer.
Internal: The internal arpeggiator and sequencer will syn-
chronize to the TRITON STUDIO’s own internal clock.
Select the Internal setting when using the TRITON STUDIO
by itself, or when you want the TRITON STUDIO to be the
master (controlling device) so that another connected exter-
nal MIDI device will synchronize to the MIDI Clock mes-
sages transmitted from the TRITON STUDIO.
External MIDI: The arpeggiator and sequencer of the TRI-
TON STUDIO will synchronize to MIDI Clock messages
transmitted from an external MIDI device connected to the
MIDI IN connector.
External mLAN: The TRITON STUDIO will synchronize to
the MIDI Clock messages transmitted by an external MIDI
device connected to the mLAN connector, and the internal
arpeggiator and internal sequencer of the TRITON STUDIO
will operate as a slave device.
If you want the TRITON STUDIO to function as a slave (the
device that is controlled) so that it synchronizes to the MIDI
Clock transmitted from an external MIDI device, set this
parameter to either External MIDI or External mLAN. The
TRITON STUDIO will respond to MIDI Common messages
and Realtime messages (Song Position Pointer, Song
SELECT, Start, Continue, and Stop) from an external
sequencer.
In Song Play mode, the TRITON STUDIO will operate
in synchronization with its own internal clock regard-
less of this setting.
Receive Ext. Realtime Commands [Off, On]
Off (unchecked): When “MIDI Clock” is set to External
MIDI or External mLAN, MIDI Common messages and
Realtime messages (Song Position Pointer, Start, Continue,
and Stop) will not be received. (Song Select will be received.)
MIDI IN
MIDI OUT
Record
Sequencer
Arpeggiator
Local
control
OFF
ON
Trigger
Tone
generator
ODD
EVEN
Another TRITON STUDIO
MIDI OUT
MIDI IN
Velocity
Curve
Aftertouch
Curve
Tone
generator
Note number
change
Play
MIDI IN
MIDI OUT
Record
Sequencer
Transpose
Scale
Velocity
Curve
Aftertouch
Curve
Tone
generator
Play
MIDI IN
MIDI OUT
Record
Sequencer
Transpose
Scale
Pitch change