Filter
Top Products
Program
P0
P1 P2 P3 P4 P5 P7 P8 P9
23
AMS (LFO1 AMS) [Off, (PEG, FEG, AEG, KT, EXT)]
Selects a source that will control the depth by which “OSC1
LFO1” will modulate the volume of oscillator 1 (“AMS List”
☞p.242).
Intensity (AMS Intensity) [–99…+99]
As the absolute value of this setting is increased, the effect of
“AMS (LFO1 AMS)” on “OSC1 LFO1” will increase. Nega-
tive (–) values will invert the LFO waveform.
LFO2 Intensity [–99…+99]
AMS (LFO2 AMS) [Off, (PEG, FEG, AEG, KT, EXT)]
Intensity (AMS Intensity) [–99…+99]
Specifies the depth and direction of the effect that “OSC1
LFO 2” (5–2) will have on the volume of oscillator 1. Refer to
the preceding sections “LFO1 Intensity”–“Intensity (AMS
Intensity).”
▼ 4–2: Page Menu Command
☞0–1A: Write Program, 1–1A: Copy Oscillator, 1–1B: Swap
Oscillator
4–3: Amp1 EG
These parameters let you create time-varying changes in the
volume of oscillator 1.
4–3a: Amp1 EG
These parameters specify how the amp 1 EG will change
over time.
Level:
Start (Start Level) [00…99]
Specifies the volume level at note-on.
If you want the note to begin at a loud level, set this to a high
value.
Attack (Attack Level) [00…99]
Specifies the volume level that will be reached after the
attack time has elapsed.
Break (Break Point Level) [00…99]
Specifies the volume level that will be reached after the
decay time has elapsed.
Sustain (Sustain Level) [00…99]
Specifies the volume level that will be maintained from after
the slope time has elapsed until note-off occurs.
Time:
Attack (Attack Time) [00…99]
Specifies the time over which the volume will change after
note-on until it reaches the attack level.
If the start level is 0, this will be the rise time of the sound.
Decay (Decay Time) [00…99]
Specifies the time over which the volume will change from
when it reaches the attack level until it reaches the break
point level.
Slope (Slope Time) [00…99]
Specifies the time over which the volume will change from
when it reaches the break point level until it reaches the sus-
tain level.
Release (Release Time) [00…99]
Specifies the time over which the volume will change after
note-off until it reaches 0.
4–3b: Level Modulation
Specifies how AMS will control the amp 1 EG level specified
in “Amp1 EG” (4–3a).
AMS (Level Mod.AMS) [Off, (KT, EXT)]
Selects the source that will control the Level parameters of
the amp 1 EG (“AMS List” ☞p.242).
Intensity (AMS Intensity) [–99…+99]
Specifies the depth and direction of the effect that “AMS
(Level Mod.AMS)” will have.
For example if “AMS (Level Mod.AMS)” is Velocity, setting
“St (AMS SW Start),” “At (AMS SW Attack),” and “Br (AMS
SW Break)” to + and setting “Intensity (AMS Intensity)” to a
positive (+) value will cause the amp 1 EG volume levels to
increase as you play more strongly. Setting “Intensity (AMS
Intensity)” to a negative (–) values will cause the amp 1 EG
volume levels to decrease as you play more strongly. With a
setting of 0, the levels will be as specified in “Amp1 EG” (4–
3a).
St (AMS SW Start) [–, 0, +]
Specifies the direction in which “AMS (Level Mod.AMS)”
will change “Start (Start Level).” If “Intensity (AMS Inten-
sity)” is set to a positive (+) value, setting this parameter to
+ will allow AMS to increase the EG level, and setting this
parameter to – will allow AMS to decrease the EG level.
With a setting of 0, no change will occur.
At (AMS SW Attack) [–, 0, +]
Specifies the direction in which “AMS (Level Mod.AMS)”
will change “Attack (Attack Level).” If “Intensity (AMS
Intensity)” is set to a positive (+) value, setting this parame-
ter to + will allow AMS to increase the EG level, and setting
this parameter to – will allow AMS to decrease the EG level.
With a setting of 0, no change will occur.
4–3
4–3a
4–3c
4–3b
Note-on
Note-off
Attack
Time
Decay
Time
Release Time
Attack Level
Sustain
Level
Time
Break Point
Start
Level
Slope
Time
Amplifier EG
Volume