Filter
Top Products
35
Combination
P0
P1 P2 P3 P4 P7 P8 P9
▼ 0–1: Page Menu Command
0–1A: Write Combination
This command writes an edited combination into the TRI-
TON STUDIO’s internal memory. Be sure to write any com-
bination that you wish to save. If the power is turned off or a
different combination selected before you write an edited
combination, your edits cannot be recovered.
For the procedure, refer to “Write Program” (Program P0: 0–
1A).
If you use “Category” to specify a category for the combina-
tion you are writing, you will be able to select that combina-
tion by its category in Combination P0: Play.
The names of the combination categories can be edited in
“Comb Cat.” (Global P4: 4–2).
You can also use the SEQUENCER [REC/WRITE] key
to write a combination in the same way as “Write Com-
bination.” Press the SEQUENCER [REC/WRITE] key
to access the dialog box, and write the combination. In
this case, the data will be written to the currently
selected combination.
0–1B: Solo Selected Timbre
The Solo function will toggle between on and off each time
you select “Solo Selected Timbre.”
1 Select the page menu command “Solo Selected Timbre.”
When you select this, a check mark will appear at the left
of “Solo Selected Timbre” in the menu, and the Solo func-
tion will be on.
2 In pages that show parameters for an individual timbre,
you can select a particular timbre to Solo (in P0: Play, Pro-
gram Select page “Bank/Program,” etc.) so that only this
timbre will sound and the other timbres will be muted.
The “Selected Timbre Information” (0–1b) in each page
will indicate [Solo.]
To solo a different timbre, select a parameter of the tim-
bre that you wish to solo.
3 To cancel the Solo function, once again select “Solo
Selected Timbre” from the page menu.
If a timbre that is muted by the Solo function has been
set to a “Status” (0–1c, 2–1b) of EXT or EX2, MIDI note-
on/off messages will not be transmitted by that timbre.
0–2: Mixer
Here you can set the pan and volume for each timbre 1–8.
0–2a: Program Category, Pan, Volume, Hold
Balance
Program Category
Part of the program category name for the timbre program is
displayed here.
Pan [RND, L001...C064...R127]
Sets the pan for each timbre 1–8.
L001...C064...R127: A setting of L001 is far left and R127 is
far right. A setting of C064 will reproduce the pan setting of
the oscillator in Program mode.
If a mono insert effect is in use, the settings you make here
will be ignored. In this case, the “Pan (CC#8)” (P8: 8–2)
parameter in Insert FX page will adjust the panning of the
sound after the insertion effect (“3. Mixer” ☞p.181).
RND: The oscillator pan will change randomly at each note-
on.
If “Status” (0–1c, 2–1b) has been set to INT, MIDI con-
trol change #10 (panpot) messages can be received to
control the setting. CC#10 values of 0 or 1 will place the
sound at far left, 64 at center, and 127 at far right.
Pan can be controlled by messages received on the
“MIDI channel” (2–1b).
0–1A
0–1B
0–1
0–1a
0–1b
0–1c
0–2a
OSC1: Amp1 Pan=L001
OSC2: Amp2 Pan=R127
Left
Center
Right
Pan (CC#10)
C064
Left
Center
Right
L032
L001
R096
R127
Left
Center
Right
Left
Center
Right
OSC1
OSC2
OSC1: Amp1 Pan=L032
OSC2: Amp2 Pan=R096
Pan (CC#10)
C064
L032
L001
R096
R127
OSC1: Amp1 Pan=C064
OSC2: Amp2 Pan=C064
Left
Center
Right
Pan (CC#10)
C064
Left
Center
Right
L032
L001
R096
R127
OSC1
OSC2